shaft height 中文意思是什麼
shaft height
解釋
中心高-
Methods ： fifty paired embalmed cadaveric humeri ( twenty - five pairs : fourteen from male donors and eleven from female donors ) were scanned in medial - lateral ( ml ) and anterior - posterior ( ap ) position according to the humeral retroversion by ct. images of the humeri in the transverse planes at the lowest border of neck ( lbn ), 20mm and 40mm distal of lbn ( lbn - 20 、 lbn - 40 ), isthmus, head - neck anterior - posterior ( hn - ap ) were obtained. sixty - one extracortical and intracortical parameters were measured exactly by image analytic computer software that included offset, head position, head - shaft angle, head to tuberosity height ( ht ), head thickness, curvature radius, articular surface arc ( sa ), neck diameter, isthmus position, proximal and distal border of isthmus, maximum coronal and sagittal diameter of medullary canal and thickness of cortical bone in four planes, including lbn, lbn - 20, lbn - 40 and isthmus
方法： 50根成對防腐肱骨（男14對，女11對）按肱骨頭扭轉角置於冠狀位和矢狀位，行肱骨全長，頭頸矢狀面，解剖頸下緣及其下20mm 、 40mm ，髓腔狹窄部四平面ct掃描，由ct軟體測量冠、矢狀位髓腔內外參數共61項，包括頭心?干軸距，頭位置，頭干角，頭?結節高度差，頭厚度，頭半徑，關節面張角，解剖頸直徑，髓腔狹窄部位置，解剖頸下緣及其下20mm 、 40mm和狹窄部四個平面髓腔的最大冠、矢狀徑，皮質骨厚度等。 -
Abstract : defining method of moving speed of vertical shaft hoist is discussed. the ralation of economy speed coefficient and hoisting height are expounded for calculating economy hoist speed. the hoist speed is adjusted according to change of hoisting assignment
文摘:論述立井提升機運行速度的確定方法，闡明經濟速度系數與提升高度的關系，為計算經濟提升速度提供依據，得出根據提升任務的變化相應地調整提升速度的結論。 -
Induction height survey through shaft
立井導入高程測量 -
Due to the existence of the eddy and the abrupt bend of the stream line, the pressure on the four faces has the distribution as follow : the lowest pressure appears at several centimeters after the angle point along the top boundary, the highest pressure appears near the center line of the vertical shaft on the bottom boundary, near the angle point, the pressure on the inner boundary decreases with the decreasing height, the pressure on the external boundary decreases slightly in the right - angle region, and increases obviously near the corner
迴流漩渦的存在，以及直彎處流線的急劇彎曲，導致壁面壓力分佈在上表面距彎點一定距離后出現壓力最小值，下表面上，在豎井中心線略偏下游的位置出現壓力最大值，豎井內表面接近彎點處出現壓力沿程降低的現象，豎井外表面壓力在進入直彎后先是沿程略有降低，在直彎角落處又明顯升高。 -
Through carrying out analysis on the aesthetics shape elements of 37 kinds of sample book, 12 shape elements for describing the contour features of industrial sewing machine, such as the elements of ratio between fuselage length and fuselage height and of shape of central part main shaft section etc. were defined
通過對37種樣本的美學形態要素進行分析，定義了描述工業縫紉機外形特徵的12個形態要素，如機身長與機身高比率、中部主軸截面等形態要素。
分享友人