shaft hole 中文意思是什麼
shaft hole
解釋
尾軸孔-
Analysis on pin hole defect of the cam shaft in remelting quenching process
凸輪軸氬弧重熔淬火過程中形成針孔缺陷的分析 -
Discuss of thrust top hole and shaft conjugation criterion
淺議推力頭孔軸配合標準 -
Disk chuck has been adopted in 74 series vertical shaft rotary die grinders, which can grind to the internal hole, excircle of large workpieces and workpieces with shoulders. die can work and grind to r - arc without removing guede - pole, and grinder head can rotate in the range from + 45o to - 45o. accordingly, the life of die is longer than before and accuracy of the die is stable
74系列立軸圓臺模具磨床採用花盤式工作臺，可對較大工件內孔、外圓和帶有臺肩的工件進行磨削，沖模模具可以不拆導向柱進行磨削及r弧磨削，提高模具使用壽命，保證模具使用精度，磨頭可旋轉45 。 -
The technology, which is developed on the basis of perfora ting techniques for oil wells and cement injection techniques, can not shoot thr ough the frozen pipe wall at predetermined ground location using energy - gatheri ng - blasting techniques, but also consolidate shaft wall rock by cement injectio n and filling along the frozen pipe and perforated hole s trajectories, achievi ng leakageproof of shaft walls and reducing vertically - added force
它利用聚能射孔爆破技術，在預定地層位置將凍結管射穿，同時在地面利用凍結管及射孔彈道對特定地層進行注漿充填加固，既可實現井壁堵漏，又能減少由於地層沉降對井壁的垂直附加力。 -
Discussion on coalmine shaft pilot hole related data processing
煤礦井筒檢查孔有關資料處理方法探討 -
Measuring dimension of shaft coupling bolts and reamer hole
軸系連接螺栓和鉆孔尺寸測量。 -
The catheter is then withdrawn back into the right ventricle, with the first disc positioned against the left ventricular wall and the connecting shaft filling the hole created by the rupture
導管接著後退進入右心室，隨著第一片定位在左心室壁上，連接軸填充心臟破裂所形成的缺損。 -
Improvement on conical hole of bored shaft in milling - boring machine
如何消除鏜床鏜桿軸向竄動 -
There is a hole in the shaft through which the air from the upper chamber enters the lower one.
腔筒中心有一孔道，壓縮空氣就是由此從上氣室進入下氣室的。 -
In the fourth chapter, the method of assembly feasibility analysis for shaft and hole feature was established. first, conformance analysis technique was build. as for lmc and mmc of rfs principle, sufficient and necessary condition was given
首先建立圓柱要素的相符性分析技術，基於漂移帶的尺寸公差語義，結合當前國標，對于lmc條件以及採用獨立原則的mmc條件，給出相符性驗證的充要條件；對于採用獨立原則與最大實體原則的mmc條件，給出相符性驗證的充分條件。 -
Sixth, a technology validation prototype system of the digital product assembly and key matching elements is developed. seventh, the secondary development of solidedge is put up and the assembly process and key matching elements. of the typical hole shaft assembly are researched. so the technology principle and implement method are validated
最後，開發了一種數字化產品裝配及關鍵要素匹配的技術驗證原型系統，在該系統中，通過對solidedge進行二次開發，以典型裝配副孔軸裝配為主要應用對象，分析了裝配過程及關鍵匹配要素，對所研究的技術原理及實現方法進行了驗證。 -
Iso thread solid shaft without pin hole
沒有銷孔的iso螺紋實心軸 -
Iso thread solid shaft with pin hole
有銷孔的iso螺紋實心軸 -
Power take - off, squared shaft drive. four hole flange
方軸驅動動力輸出軸.孔法蘭 -
Physical model test and study on shaft excavation by one - step deep - hole blasting
一次爆破成井物理模型試驗研究 -
Numerical simulation on cutting mode of shaft excavation by one - step deep - hole blasting in hard rock
堅硬巖石一次爆破成井掏槽方式的數值模擬研究 -
Application of deep hole smooth blasting in mine shaft construction
深孔光面爆破在立井施工中的應用 -
From several strain measurements of members, such as a tension plate with only a hole, or double troughs and a torsion shaft with a hole, the method is effective
該文對帶孔或槽的拉伸試件和帶孔的圓軸試件應變測量數據進行了分析計算，結果表明這是一種較實用的方法。 -
Through comparative analysis to the test data of tow sampling methods in drilling hole and sampling method in shaft, it was found out by the author that the drilling sampling method has obvious disturbance and depression to the soil sample, which caused the soil sample ' s dry density to be increased, porosity ratio to be decreased, filtration coefficient to be decreased, and modulus of compression to be increased
筆者通過對鉆孔兩種方法獲取的土樣與豎井土樣試驗數據的對比發現，鉆孔取樣對土樣有明顯的擾動和壓密作用，造成了土的干密度增大、孔隙比減小、滲透系數降低、壓縮模量增大。 -
Initial break and smooth blasting in deep bore hole blasting of mine shaft excavation
立井深孔掘進爆破中的掏槽和光爆
分享友人