single liquid crystal 中文意思是什麼
single liquid crystal
解釋
單液晶-
Using domestic strained integrated resistor as weighing sensor, at89c52 single chip as control unit, combined with arithmetical magnification, analogtodigital conversion ( a / d ), real time clock, liquid crystal display ( lcd ), and series communication interface, a minitype automatic weighing lysimeter is developed. that made measurement of evapotranspiration become conveniently and effectively in studying on water use of crops
為了方便、有效地測定植物的蒸散，為水分利用研究提供價廉物美、簡單易用的儀器，本研究利用國產的集成電阻應變式稱重傳感器，採用at89c52單片機作為控制單元，結合運算放大、模數轉換、實時時鐘、液晶顯示、數據存儲、串列通信等外圍介面電路，研製了小型自動稱重式蒸散儀。 -
According to the guidline, two nd : yag lasers have been designed and set up, one is end - pumped by lower output power ld using a selfoc micro lens, and the other is end - pumped by high output power ld using a pair of lenses are designed, and the characteristics such as output power and power stabilization of both solid - state lasers are investigated. thirdly, when an empty liquid crystal cell is inserted in the cavity of the nd : yag laser pumped by high power ld, the laser can operates in single axial mode. finally, according to the relationship between the laser output power and the longnitudinal a ld - end - pumped nd : yag laser sensor for displacement measurement has been investigated theoretically and demonstrated experimently, the results indicate that when the mean radius of pumping inside the laser cavity is far less than that of the oscilating laser mode, the exponential of the output power is a gauss function of the longitudinal positon of focused spot of ld pumping beam, both the measurement range and the sensitivity are dependent on the incident pumping power, as the incident pumping power is increased, the measurement range is enlarged and the sensitivity is improve d
本文首先介紹了ld泵浦nd ： yag激光器的發展狀況、主要特性及其應用，從四能級速率方程出發，推導了ld泵浦nd ： yag激光器的閾值、輸出功率和斜效率的表達式，並簡述了激光器的工作原理、結構型式和倍頻方法；其次，以空間相關的速率方程為基礎，提出了ld端面泵浦nd ： yag激光器的設計方法，給出了一定泵浦耦合方式下，振蕩光模尺寸、最佳輸出耦合率、泵浦光模尺寸、泵浦光焦斑位置等參數的選取依據，以此為依據，設計了自聚焦透鏡耦合小功率ld泵浦nd ： yag激光器和透鏡組耦合高功率ld泵浦nd ： yag激光器，對激光器的輸出功率和功率穩定性等特性進行了實驗研究；再次，在帶尾纖輸出的高功率ld泵浦nd ： yag激光腔內插入一隻空液晶盒，觀察到了激光器以單縱模運轉；最後，根據泵浦光焦斑端面位置對激光輸出功率的影響規律，提出了ld端面泵浦nd ： yag激光位移傳感新方法，並進行了理論和實驗研究，研究結果表明：當激光晶體內泵浦光平均光斑半徑遠小於振西安理工大學碩士學位論文蕩光束腰半徑時，激光輸出功率的自然指數與泵浦光焦斑的縱向位置成高斯變化規律，測量范圍和靈敏度依賴于泵浦功率，隨著泵浦功率的增加，測量范圍擴大，靈敏度提高，當端面泵浦功率為7 . 24w （最大輸出功率為1 . 926w ）時，激光位移傳感器的測量范圍和靈敏度分別是13 . 045mm和0 . 148mw / pm 。 -
A novel measurement and control system ( mcs ) used in hv flameproof switchgear has been established based on the 80c196kb single - chip microprocessor, by which electrical faults such as short circuit, over - load, over - voltage, open circuit, earth leakage and so on can be automatically distinguished and processed, and with the exception of this, the insulation degree of the double screen cables is monitored on - line. the operating condition and fault parameters can be displayed in turn with liquid crystal display
該系統能自動判斷短路、過載、過壓、欠壓、漏電等故障，並對高壓電纜的絕緣水平進行實時監測，大屏幕液晶顯示器實現了電太原理工大學碩士學位論文網參數的輪流顯示，通過撥碼盤輸入系統各項整定參數，真正實現了保護系統數字化。 -
The electrical - controlled appliance is the core part of the machine for body functional rehabilitation, the single slice microcomputer ' s function is data processing and controlling, the power supply provides work voltage to the single slice microcomputer and other parts, keyboard inputs data, liquid crystal display shows data of motion and data which establish at first, motor ' s driver drive motor by control - signal
肢體運動康復機的核心部分是電控裝置，單片機起數據處理及控制等作用，電源部分提供給單片機及其他部件工作電壓，鍵盤提供輸入數據，顯示器顯示運動數據及預設數據，電機驅動部分通過控制信號來驅動電機工作。 -
Electrical - controlled appliance includes single slice microcomputef, power supply, keyboard, liquid crystal display. the machine for body functional rehabilitation is controlled by enactment of five parameters, which are speed, range, position, frequency, time. the enactment of the five adjustable parameters used to realize six function that are anns stretching and circumrotating, wrist swing, finger stretching, crura anuckle stretching, anklebone swing
將肢體運動康復機本身選用的六項功能用以下五個參數的設定來控制，即用速度、幅度、位置、頻率、時間這五個可調參數的控制來實現肢體運動康復機中上肢手臂伸屈、手臂旋轉、腕關節上下左右擺動、手指伸屈、下肢膝關節伸屈、踝關節上下左右擺動六個功能。 -
Hot - press is a device of industrial manufacture designed to heat and press the workpieces. we designed this control system to fit the hot - press. its center unit is 89c55 single - chip microcontroller, and its output interface is a color lcd ( liquid crystal display )
熱壓機是一種對工件加熱加壓的工業生產設備，我們設計的與熱壓機配套的控制系統，以89c55單片機為中心器件，選用了彩色液晶顯示屏作為輸出界面，實現了按工藝參數的自動運行，用改進的pid演算法對溫度和壓力實現了良好的控制，並具有快捷有效的pid參數自整定的能力。
分享友人