sinter system 中文意思是什麼

sinter system 解釋
燒結輸送系統
  • sinter : n. 1. 【地質學；地理學】泉華〈礦泉四周沉澱的結晶巖石〉。2. 鐵的銹皮；【冶金】熔渣，燒結物。vt. 燒結。
  • system : n 1 體系，系統；分類法；組織；設備，裝置。2 方式；方法；作業方法。3 制度；主義。4 次序，規律。5 ...
  1. At present, our country is the largest producer and consumer in the horniness - alloy scopes. but now, this stove depends on import, hip - sinter stove ’ s self - develop and corresponding control system has important apply value

    目前我國是世界上最大的硬質合金生產與消費國，但生產所需的燒結爐仍主要依賴進口，自主研製低壓真空燒結爐及配套的控制系統無疑具有重要的應用價值。
  2. Abstract : in this paper, two tests are described on air leakage of sinter machine in 2 sintering plant of xiangtan iron and steel co. according to the test results, on the base of analysis and discussion, a series of measures on decreasing air leakage of sinter machine are putted forwored from sealed devices, lubricating oil system, maintenance and management etc. an effective and feasible way is supplied for energy saving and increasing production, decreasding production cost, increasing economy benefit of sintering process

    文摘:通過對湘鋼二燒燒結機漏風率的兩次測試和結果分析，從密封裝置、潤滑系統、附件結構的改進等方面提出了一系列降低漏風率的對策，為燒結工序的增產節能，降低生產成本，提高經濟效益提供了一條行之有效的途徑。
  3. Analysis on breakage and system fault on universal shaft on cold - hot screen of sinter machine

    燒結機冷熱篩萬向傳動軸斷裂及系統故障分析
  4. According to control system requirements of hip - sinter stove, the thesis selected plc of s7 - 300 series of siemens as main controller to autocontrol produce process, and the industry person computer which produced by advantech ltd. and hmi which produced by proface ltd. as the monitor computer, which composed plural computer control system

    根據低壓真空燒結爐控制系統需求分析，選用了西門子公司的s7 - 300系列plc作為主控制器對生產過程進行過程自動控制，以及研華工控機和proface公司觸摸屏作為監控計算機，構建了一個低壓真空燒結爐兩級計算機控制系統。
  5. At the base of participating in the system design and debug of the dy - 500 hip - sinter low - pressure and vacuum sinter stove which is investigated by the zigong horniness - alloy ltd. this paper conclude the practice and work, according to the sense and the embed analysis, this paper including : aim at hip - sinter stove, analyse technics principle of the dewaxing, the vacuum sintering and the hot isostatic pressing by low pressure

    在參與自貢硬質合金有限責任公司研製的dy - 500型低壓真空燒結爐自動控制系統設計和調試的基礎上，本論文對實踐工作進行了總結與提高。根據現場經驗和深入分析，論文的主要內容有:針對低壓真空燒結爐，分析脫蠟、真空燒結、低壓熱等靜壓工藝原理，並論述了溫度、真空度、壓力三個主要因素對生產過程的影響。
  6. According to the types select of sensor and transducer and the satistic mount of i / o of the control system of hip - sinter stove, the thesis configured and select the types of control system hardwares. then, designed the plc autocontrol program of hip - sinter stove by the step 7 v5. 2 software and the monitor program of montor computer by the wincc v6 monitor conifigure software. consequently, it improved the whole performance of the stove a lot

    根據低壓真空燒結爐控制系統i / o的統計和傳感器的選型，對控制系統硬體進行了配置和選型，並採用step7v5 . 2軟體編制了低壓真空燒結爐plc自動控製程序以及利用winccv6監控組態軟體完成了監控計算機上的監控軟體開發，大大改善爐子的整體性能。
  7. Distribution of mixture for adding fuel separately in the micropellet sintering processing must be notice, otherwise the heat system in sinter would be destroyed

    燃料分加小球團燒結時必須注意混合料布料問題，否則會破壞燒結過程熱制度。
  8. Abstract : take 3 sinter plant of maanshan i & amp; s co. as an instance, the software of operation data information management system and its main fuctions were presented in this paper

    文摘:本文以馬鋼三燒為例，介紹了生產數據信息管理系統軟體設計的概況及主要功能。
  9. At present, there was n ' t reported about optimization of mixing and transport line system at raw material yard inside and outside of our country, there are only similar mixing model in sinter and steel - making plant

    目前國內外對于原料場配料與作業線的系統優化設計還未見報道，只有燒結廠、煉鋼廠有類似的配料模型。而且可用於指導原料場生產的系統優化方案也未見報道投入使用。
  10. This thesis comes from a practical industry task named " the system of on - line monitoring on the chief axis of single - roller crusher in the no. 2 workshop of sinter factory ， wuhan iron and steel group corporation.

    =本論文來源於工業實際課題，課題名稱為「武鋼燒結廠二車間單輥破碎機主軸扭矩在線監測系統」 。
  11. On the base of analyzed the actual on site problem of the single - roller crusher in sinter factory at present, and combining the development of toque sensor, a kind of non - contact toque sensor has been turned out, which responded the production process and represented modern technology level. according to the recent progress of computer aided test ( cat ), the virtual instrument ( vi ) technology has been applied when designed the measure system

    在研究過程中，通過對目前燒結廠單輥破碎機存在的問題做現場實際分析，結合當今扭矩傳感器發展水平研製了技術含量較高、符合現場生產實際的非接觸型扭矩傳感器；根據計算機輔助測試技術的最新進展，採用虛擬儀器技術設計了測試系統。
分享友人
分享到 Line

分享到臉書