sintering treatment 中文意思是什麼

sintering treatment 解釋
燒結處理
  • treatment : n 待遇；作業；處理，處置；討論，論述；【醫學】治療，療法；（種子的）消毒（處理）。 preferential t...
  1. On the base of the analysis on the advanced technology of hard ferrite in foreign country, the main procedures of preparing hard ferrite pre - sintering material are determined as follows : first, the ferrite oxides coming from the main cold rolling line and strontium carbonate are conveyed to storage tank by gas power and weighed automatically according to the demands of constituent composition. and then they are mixed and grinded by using method of wet treatment. finally the mixtures is transported to the devices of storage by transporting pump

    在分析國外先進的永磁鐵氧體生產工藝的基礎上，確定了生產高檔永磁鐵氧體預燒料的主要過程：首先，利用攀鋼冷軋鐵紅為主要原料，將氧化鐵紅及碳酸鍶採用氣力輸送至貯料料倉，經自動稱量裝置，按工藝配方稱量後分別由氧化鐵紅及碳酸鍶發送罐氣力輸送進入預混攪拌筒加水攪拌，然後再送入混磨機濕法混磨；最後，混合物經輸送泵輸送至料漿存儲裝置，經定量進料泵定量輸送至回轉窯進行濕法預燒，預燒料經緩冷至室溫后，再球磨。
  2. Pulse electric current heat treatment ( pecht ) developed by sodick, ltd., of japan, is a recently developed material processing method which consists of spark plasma sintering and welding, plasma activated sintering and welding, big pulse electric current ( bpec ) diffusion welding etc. the following are basic merits of pecht : rapid heating and cooling ; short sintering or welding time ; lowering sintering or welding temperature

    脈沖電流熱加工（ pulseelectriccurrentheattreatment ，比如燒結，焊接等）是九十年代發展起來的一種材料快速制備新技術，它包括放電等離子燒結與焊接、等離子活化燒結與焊接、脈沖大電流擴散焊接等。它具有升溫、降溫速度快、能在較低的溫度下燒結或焊接以及時間短的特點。
  3. It shows with the increase of the amount of the mo in the si - mo infiltrant, the density of the infiltrated materials with the same performs increased, but the amount of the free carbon and pore also increased. it was the result of the capillary chocking - off caused by the separation of the mosj2 from the alloy infiltrant during the sintering process. after th thermal treatment at 2050, the amount of the free carbon and pore decreased. also. another cause for the unfully conversion of c into sic was the gas pressure. larger than the capillary force

    實驗表明，對于同一坯體，隨著si - mo熔體中mo含量的增加，浸滲所得材料的密度隨之增加，但是，材料中的殘留c 、氣孔相的含量亦隨之增加。這是由於反應浸滲時，熔體中析出的mosi _ 2阻塞毛細管造成的。含殘留c 、氣孔相的材料進行高溫（ 2050 ）熱處理后，材料中殘留c 、氣孔相的含量大大減少。
  4. Large pieces of rock are only suitable for use as road surfaces in the form of fine gravel, run - of - mine coal needs to undergo a size reduction prior to further treatment, and lumps of ore need to be crushed to small pieces because sintering plants require feed material with a high degree of fineness

    公司的目標是生產破碎機和洗礦機。只有砂礫狀的巖塊才適合於路面，原煤必須首先要被擊碎才能被加以利用，礦石必須被搗碎，這是因為燒結設備只能處理細微物料。
  5. Under the background of correlative research project, the method of selective laser sintering has been used in the researching work. polymer - coated high - temperature alloy powder have been first developed successfully in our nation. the laser sintering and post - treatment process of high - temperature alloy parts have been systematically studied, which lay the foundation for its engineering application

    在國內首先研製成功了覆膜高溫合金粉末及其制備工藝，並對其激光燒結成型和后處理工藝進行了系統的實驗研究，為該項技術的工程化應用打下了基礎。
  6. Thorough treatment of smoke and dust at head part of sintering machine

    燒結機機頭煙塵深度治理實踐
  7. ( 3 ) solid solution with good solid solution ability were acquired by solid soluting treatment for 25 min at 540 c, 560 c and 580 c, respectively, after that water quenching was carried on. in the case of 580 c, the coarseness of the precipitation at grain boundaries did not happen, equi - part 120 did not emerge at the intersection of three grains, these suggest that over sintering did not happen

    6013合金實驗熱軋板材經固溶處理後於180時效4小時達到峰值硬度； （ 3 ） 540 、 560 、和580固溶處理25min 、水淬，得到了固溶充分的固溶體， 580的情況下晶界析出相未粗化、三晶粒交界處的角度未出現等分的120 ，表明未發生過燒。
  8. Because of its excellent properties, such as high strength, high module, wear resisting, and etc., sicp was added to ferroalloy as a reinforce phase. but the intrinsic difference between the bonds led to poor fabrication of the composites. in this paper, the effects of alloying, sintering, and heat - treatment on the properties and microstructures of sicp / ferroalloy - based composites were studied, : it was found that sic particles reacted with ferroalloy when sintered in 1100

    碳化硅因其高強度、高模量、耐熱、耐磨等優良性能而被作為顆粒增強體來制備鐵基復合材料，但因其共價鍵與鐵基體的金屬鍵之間的本質區別導致兩者復合困難，本文擬從基體合金化、燒結及熱處理工藝等方面對鐵合金基復合材料組織與性能的影響進行考察，具體內容如下：加入fe - cu - c基體中的sicp顆粒， 1100燒結時就已經開始發生分解，但反應不強烈，在顆粒表面鍍鎳可以延緩基顆粒與基體之間的反應。
  9. Ceramic grain filters ard made of refined pottery clays added with certain modifiers, and processed of grinding, mixing, shaping and high temperature sintering. they do not contain any substances that harmful to people or environment. they are hard and rough in surface, porous inside the structure, and have the advantages of high mechanical strength, large specific surface area and porosity. when used in water treatment, they behave a activated surface property, a great amount of pollutant entrapment, less water head loss in the filter bed, lower consumption of back - flush water, stable in chemical and gbiologic property, and long service life, ceramic grain filters is a new and efficient filter material to increase the water yield, upgrade the water quality, and save chemicals and energy

    陶粒濾料是以精製陶土為主要原料，摻加適量改性劑，經粉碎，混練，成型和高溫煅燒而製成的，不含任何對人體和環境有害的物質.其表面堅硬，粗糙，內部疏鬆，多孔，具有機械強度高，比表面積大，孔隙率大的特性.用於水處理中，具有表面性狀好，截污能力強，過濾水頭損失小，反沖洗耗水量低，化學穩定性和生物學穩定性好，使用壽命長的特點.陶粒濾料是一種能增加水產量，提高出水質量，節省藥劑和能耗的新型高效過濾材料
  10. Through the improvement for existing process of steelmaking dust removal sludge treatment system, this kind of sludge can be carried to the sintering burden directly through pipelines for the purpose of saving the energy, decreasing the consumption, reducing the pollution and increasing the benefit

    通過對煉鋼除塵泥漿處理系統現有工藝的改造，將煉鋼除塵泥漿直接用管道送燒結配料，達到「節能降耗、減污增效」的目的。
  11. Abstract : through the improvement for existing process of steelmaking dust removal sludge treatment system, this kind of sludge can be carried to the sintering burden directly through pipelines for the purpose of saving the energy, decreasing the consumption, reducing the pollution and increasing the benefit

    文摘:通過對煉鋼除塵泥漿處理系統現有工藝的改造，將煉鋼除塵泥漿直接用管道送燒結配料，達到「節能降耗、減污增效」的目的。
  12. As for the change of reaction temperature, a good appearance of microspheres will be observed. after heat treatment we obtain the mesoporous sio2 microspheres, the morphology, size and size distribution of microspheres before and after sintering were investigated by using the scanning electron microscopy ( sem ). the desorption of water and ethanol and decompostion of polymers in microspheres were analyzed by using tg - dsc machine

    當r 1時將導致微球產生破裂，而r 4時則生成凝膠狀物質；其他條件不變時，微球形貌隨ph值的增大逐漸變差，最終破裂；乙醇含量增大時，微球粒徑逐漸增大；而隨著反應時間的進行，顆粒逐漸長大，微球形貌不斷完善，表面逐漸平滑；反應溫度的變化會得到更光滑的微球表面，微球粒徑隨之增大。
  13. The company iso9001 - 2000 quality system certification, the company specialized research and development of low - power, high - efficiency high - quality vacuum heat treatment furnace and vacuum brazing furnace, vacuum sintering furnace

    公司通過iso9001 - 2000質量體系認證，公司專門研製開發低能耗、高效益高品質的真空熱處理爐和真空釬焊爐、真空燒結爐。
  14. In order to overcome the influence of the technology factor in active molybdenum - manganese metallization, the formulation, raw material treatment, painting method and sintering process are improved in alumina ceramics metallization, which can raise the technique level, product quality and uniform

    摘要針對影響氧化鋁陶瓷活化鉬錳法金屬化的工藝因素，在配方、原料處理、塗敷方式、燒結等方面進行改進，提高工藝水平，保證質量穩定性、一致性。
  15. The preparation process of sintered psc involves powder purifying, pressed powder compact preparation, sintering process and final treatment

    Psc的制備過程包括粉末的凈化、壓坯的壓制、燒結過程和樣品的后處理。
  16. The preparation process of sintered psc involved powder purifying, pressed powder compact preparation, sintering process and final treatment

    多孔碳化硅的制備過程包括原始粉末的凈化、壓坯的壓制、燒結過程和燒結樣品的后續處理。
  17. The course mainly introduces the characteristic of starting ceramic materials, preparation of ceramic powers, machining and treatment, forming and sintering process, and basic sintering principles of ceramics

    主要講述了陶瓷原材料的特性、陶瓷粉體制備、加工處理、成型和燒結工藝，以及燒結的基本原理。
  18. Doping of tio2 moo3 cro3 peo also improves the stability of sols, the performance of this electrochromic materials. when the optimum sintering treatment temperature is 200c, the ec layer has excellent electrochemistry performance and firmly integrated with glass substrate. doping of tio2 improves the stability of ceo2 and change the electrochemistry performance of sols markedly

    本文研究了該全固態電致變色器件的顏色變化、響應時間、電化學性能、保存時間，並著重研究了電致變色層的循環次數、晶型結構、以及其前驅物的均勻性、穩定性和適宜的粘度。
  19. A case study of project subsequent appraisement of the off - gas treatment of lead sintering machine is given in this article, and the advance preparations, construction and completion of the project are summarized ; and the main technical and economic index are analyzed in comparison in this article. the project is graded a by use of project success appraisement chart

    在此基礎上運用系統評價法對株洲冶煉集團公司鉛燒結煙氣治理項目進行了后評價，評價中對項目前期準備工作、建設實施和建成投產情況做認真的總結，對項目完成前後的主要技術經濟指標進行了對比分析，並用項目成功度評價表進行了分級評價，根據對各項目指標的相關重要性及評定等級評價，項目總評為a 。
  20. In this paper, systemic experiments are performed on the compositions, processes, microstructures and properties of some high quality pm inserts. main procedures such as mixing, compaction, sintering, re - compaction, re - sintering, heat - treatment, properties detection and mould design and so on are included in these experiments

    本文對幾種高性能粉末冶金搖臂鑲塊的成分、工藝、組織和性能等進行了系統的實驗研究，包括混粉、初壓、初燒、復壓、復燒、后續熱處理、性能檢測、現場模具設計等。
分享友人
分享到 Line

分享到臉書