slot width 中文意思是什麼

slot width 解釋
槽寬
  • slot : n 1 狹縫，窄孔；【機械工程】漕溝；自動售貨機投錢口。2 【航空】翼縫。3 〈美口〉（集體或系列中的）...
  • width : n. 廣闊；寬度；幅度；（布匹的）門面；幅員；廣博。 12 feet in width 闊 12 英尺。 width in the clear 【林業】除皮直徑。
  1. In the dissertation, the effects of the air slide - film damping on the capacitive accelerometers having different slot structures which are completely or partly etched, and fabricated by the anodic bonding between silicon and glass and bulk silicon micromachining process are researched by changing the distance between the moving structure and substrate, the thickness of the structure, the width of the completely etched slot structure, the depth of the partly etched slot structure according to the two well known air slide - film damping models

    對于橫向運動的體微機械器件，其周圍空氣表現為滑膜阻尼。本文基於滑膜阻尼的兩個模型，通過改變振子與襯底的間距、振子的厚度、刻透的柵槽的寬度、沒有刻透的柵槽的深度等參數，研究了這些參數對硅?玻璃鍵合工藝製作的體硅微機械電容式傳感器阻尼特性的影響。
  2. Inner slot width

    小端槽寬
  3. Influence of slot width on transmission properties of frequency selective surfaces

    縫隙寬度對頻率選擇表面透波特性的影響
  4. Mean slot width

    中點齒槽寬
  5. Generally speaking, the increase of the slot length and width can make the resonance frequency low, which is not the longer the better, however

    一般來說，縫隙長、寬的增加可使諧振頻率點降低，而較大的縫寬也降低了貼片的有效輻射面積，使增益降低，所以需要折衷協調。
  6. The automobile outline size ' s measurement machine is the large outline size measurement equipment designed for the traffic police and vehicles management section, and used for private packing, privately changed the vehicles and over - size vehicles, especially for checking those vehicles, their length, width, height, the car slot height and the distance of auto axis, or for determining whether the vehicle ’ s size has extended the prescribed limit

    汽車輪廓尺寸測量機是為公安交警車輛管理部門研製的大型輪廓尺寸測量設備。用於對私裝私改車輛及尺寸超限車輛的檢測、查驗和稽查。汽車輪廓尺寸測量機的功能是對可疑車輛的輪廓尺寸長度、寬度、高度、車槽高度及軸距、輪距實施自動化測量，並對其尺寸是否超限作出評判。
  7. The more poles mode, the unequal pole width mode ; the low - frequency slot harmonic modulation mode and the mode of changing end magnetic conductance are presented, and these designing method can efficiently weaken the end effect and decrease the wave of the thrust

    提出的採用多極電機方式；初級與次級極距不等的方式；齒諧波低頻調制方式和改變電機兩端部磁導的方式等電機的設計原則和方法，都可有效地削弱端部效應，減小推力的波動。
  8. Minimum slot width

    最小槽寬
  9. Slot - width taper

    槽寬收縮
  10. Outer slot width

    大端槽寬
  11. Width of line slot

    線槽寬度規格：
  12. A permanent magnet synchronous motor is selected so that the system could work excellently. multiform measures are taken to weakening the torque ripple, such as adopting stator - flume, choosing right ratio of magnet - width and slot - width, and programming properly. a permanent magnet synchronous motor cad software is worked out for predigesting the design of the motor

    力矩脈動是衡量交流伺服系統性能優劣的重要指標，為達到理想的控制效果，系統採用正弦波驅動的稀土永磁同步電動機作為執行元件，電機本體的設計綜合採用定子斜槽、將轉子永磁體連續移位、合理選擇永磁體寬度和齒槽寬度比等方法，基本消除了齒槽轉矩；對于紋波轉矩，系統採用軟體的方式加以削弱和補償。
  13. The piv technique is applied to visually measure the flow field in the vicinity of the exit of slot turbulent jet with limited width discharged into cross - flow from bottom

    摘要本文應用piv流動顯示技術詳細測量了有限寬度窄縫射流從底部射入橫流的流場結構。
  14. With the increase of the width of the slot, the e - field in the middle of the slot will decrease gradually, while the power in it increase gradually, the e - field and peak power in the cavity will also increase gradually

    隨著孔縫寬度的增加，共振增強頻率點有所偏移，孔縫中心耦合的電場強度逐漸減小，而孔縫中心耦合的功率峰值逐漸增大，腔體內耦合的電場強度和功率峰值也逐漸增大。
分享友人
分享到 Line

分享到臉書