solid hardness 中文意思是什麼
solid hardness
解釋
實體硬度-
The unstable solid solution would disintegrate and transform into carbide phases in these systems of sisocso, tisocso and zrsocso, based on the increase of free energy introduced by the effect mechanical alloying. for the system of wsocso, the solid solution had not transformed into tungsten carbides but an amorphous phase, which was different from those systems. the exist of fe in these experiments, which came from the abrasion of ball - milling tool because of the higher hardness of w and w - c solid solution, would induce the crystalline - to - amorphous phase transformation during milling
C50球磨體系中，繼續球磨時，不穩定的固溶體在機械合金化作用下，由於體系能量提高，會發生分解相變，從而可以形成碳化物；對于w扣c50球磨體系， w ? c固溶體具有較高的硬度，磨削不銹鋼質的球磨介質和球磨容器，而引入雜質，其中fe會促使固溶體向非晶相轉變。 -
The degrees of crystallinity of pure ptfe under the different conditions of water cooling, air cooling and furnace - varying cooling were made comparison by xrd. the thermal stability of pure ptfe and solid lubricant was analyzed by dsc - tg ; the composition and valence state of elements in the surface of carbon fiber, solid lubricant before and after friction test and lubricant transfer film were characterized by xps ; the frictional property of solid lubricant was tested by pin and disk test rig. the frictional wear property of solid lubricant between embedded bearing sleeve and steel axle friction pair ring was tested by special simulate test machine, the hardness of solid lubricant was tested by pm ; the compression strength of solid lubricant was tested by material test machine
用sem表徵原料微觀結構、摩擦表面及潤滑轉移膜表面形貌：用xrd進行原料物相分析，及比較水冷卻、空氣冷卻、隨爐冷卻三種工藝條件下的純聚四氟乙烯樹脂的結晶度；用dsc - tg分析純聚四氟乙烯樹脂及固體潤滑劑的熱穩定性；用xps表徵碳纖維表面、固體潤滑劑摩擦前後表面、潤滑轉移膜表面的元素組成、價態變化；用銷盤式摩擦磨損試驗機對固體潤滑劑進行摩擦性能測試；採用專用的臺架模擬試驗機對固體潤滑劑鑲嵌軸承套與鋼軸摩擦副間的摩擦磨損性能進行測定；用萊次偏光顯微鏡（ pm ）測試固體潤滑劑的硬度；用材料試驗機測試固體潤滑劑的抗壓強度等。 -
Abstract : a new simulating method is established for the calcul ation of the hardness profile of high - carbon - concentration deep - carburization, on the basis of analyzing this process and taking into account the influence o f carbide solution and dissolution, carbon - concentration and temperature on the diffusion behavior, and the influence of the environment factor on carbon trans fer through the gas - solid interface
文摘:在對高濃度深層滲碳的特點進行分析的基礎上，考慮到碳化物的析出與溶解、溫度及碳濃度對擴散行為的影響，氣氛環境對相界面碳傳遞過程的影響，淬火烈度對滲碳層冷卻效果的影響，提出了一種新的模擬高濃度深層滲碳滲層硬度分佈的方法。 -
Sintering or friction all brought about chemical change in the surface of solid lubricant and the change of valen ce state of mo, s, fe and so on ; the micro - hardness of pure ptfe was minimum and the surface - hardness of solid lubricant was increased with the increase of additional packing filler in formula ; the compressive strength of pure ptfe was minimum and its compressive strength could be increased notably by adding organic and inorganic filler. but not more additional amount, more notable increase of compre
、 feso4 、 cus等物質;燒結及摩擦均使固體潤滑劑表面發生化學變化，使mo 、 s 、 fe等元素的價態發生變化;純ptfe的顯微硬度最低，固體潤滑劑的表面硬度基本是隨著填料加入量的增加而增加的;純ptfe的抗壓強度最低，在ptfe樹脂中加入無機填料均可明顯提高其抗壓強度，但並不是加入量越多，抗壓強度提高越明顯。 -
Plain bearings ; hardness testing of bearing metals ; solid materials
滑動軸承.軸承金屬的硬度檢驗.固體材料 -
And the microstructure, the hardness and the wear resistance properties of complicated parts had also been studied and analyzed. the results showed that under the same experiment condition, the semi - solid flow and deformation properties of the composites increased with the increasing of the sic particles " volume fraction which below 12 %, that he composite reinforced with different volume fraction of sic particles were die - cast into complicated parts successfully, that sic particles dispersed even more uniformly in their complicated parts, and that he complicated parts " hardness was better than the composites "
結果表明，在sic顆粒體積含量低於12的情況下， sic顆粒含量越高，復合材料的成型性能越好； sic顆粒增強鋁基復合材料能夠用壓鑄的方法制備復雜壓鑄件； sic顆粒在壓鑄件中分佈更為均勻，且呈單顆粒；壓鑄件的硬度比復合材料鑄錠的硬度高； sic顆粒增強鋁基復合材料的壓鑄件耐磨性高於復合材料鑄錠。 -
The microstructure, the hardness and the wear resistance properties of the composites fabricated by semi - solid casting has been studied and analyzed metallographic analysis indicated that sic particles dispersed uniformly in the composites
本文採用半固態復合鑄造法制備了sic顆粒增強鋁基復合材料，並對這一系列材料的微觀組織、硬度及耐磨性能進行了研究與分析。 -
Testing of carbonaceous materials - rockwell hardness test - ball indentation method ; solid materials
碳素材料試驗.洛氏硬度試驗.布式硬度試驗方法.固體材 -
And the microstructure, the hardness and the wear resistance properties of the composites fabricated by semi - solid casting had been studied and analyzed
本文採用半固態復合鑄造法制備了sic顆粒增強鋁基復合材料，同時研究了復合材料的微觀組織、硬度和耐磨性能。
分享友人