speed limit point 中文意思是什麼

speed limit point 解釋
速度極限點
  • speed : n 1 快，迅速。2 速率，速度。3 （汽車的）變速器，排擋。4 （膠片，照相紙）感光速度。5 〈古語〉興隆...
  • limit : n. 1. 界限，界線；邊界。2. 極限，限度；限制。3. 〈pl. 〉范圍，范域。4. 限價；限額；賭注限額；獵物限額。vt. 1. 限制，限定。2. 減少。adj. -able
  • point : n 1 尖頭，尖端；尖頭器具；〈美國〉筆尖；接種針，雕刻針，編織針；小岬，小地角；【拳擊】下巴。2 【...
  1. In exercise of the powers vested in me under section of the road traffic ordinance, chapter 374, i hereby direct that with effect from 10. 00 a. m. on 22 december 2006, the southbound carriageway of wan po road from a point about 70 metres south of its junction with chiu shun road roundabout to its junction with pung loi road will be subject to a speed limit of 50 kilometers per hour

    本人現行使道路交通條例第374章第40 2 a條所賦予的權力，下令由2006年12月22日上午10時起，環保大道由其與昭信路迴旋處的交界以南約70米處起，至其與蓬萊路的交界處止的南行車路，將實施每小時50公里車速限制。
  2. What banker applies at most is tall open quotation, amount of gather contest price is very large, but share price rushs on the powerful momentum for afterwards eve hard, turn around downward, to the limit of one ' s capacity drops broken all valence, although dish in your writing accepts the order, but share price goes cast apparent be enslaved to be enslaved to all of valence press instead, point of price of before one day of closing quotation also does not have a bit resistance, all the speed of price be issued to lower levels and share price keep basically consistent, because be banker concentration, shipment causes

    莊家運用得最多的是高開盤，集合競價量很大，但股價難以為繼前日的強勁勢頭上沖，掉頭向下，放量跌破均價，雖然盤中有大筆接單，但股價走拋明顯受制於均價的反壓，前一日收盤價處也沒有絲毫反抗力，均價下行的速度與股價基本保持一致，因為是莊家集中出貨造成的。
  3. Equations of mesh, shorting contact line, undercutting limit line, meshing limit lines and the existence conditions, angle between the direction of relative speed and the direction of contact line, induced normal curvature about every point on the contact line are established. moreover, the paper also theoretically analyzed the error of the grinded gear surface. on the basis of the theory, the computer program is worked out to automatically produce the contact line and the boundary curves of mesh. analysis of meshing circs under different parameters can be done so that we can gain the best process condition

    首先對漸開面二次包絡理論進行了深入的探討，推導出了兩次嚙合的嚙合方程式、瞬時接觸線方程式、根切界限線方程式、嚙合界限線的方程式及其存在條件，相對運動速度方向與接觸線方向的夾角及接觸線上各點的誘導法曲率；此外，還對磨齒后工件的齒面誤差進行了理論分析；並在理論基礎上編制了相應的計算機程序，自動生成接觸線族及嚙合界限線，對不同參數條件下的嚙合情況進行分析，可以使工藝條件達到最佳狀態；最後研究了磨齒裝置，設計了磨齒機的傳動系統。
  4. On 17 march 2006, the section of eastbound carriageway of tseung kwan o road from its junction with the slip road leading to sau mau ping road to a point about 60 metres east of the same junction will be subject to a speed limit of 50 kilometres per hour

    10時起，將軍澳道東行車道由其與連接往秀茂坪道的支路的交界處起，至同一交界以東
  5. In exercise of the powers vested in me under section 40 of the road traffic ordinance, chapter 374, i hereby direct that with effect from 1 january 2007 to 2 november 2007, the section of lin cheung road southbound carriageway from a point about 110 metres north of its junction with the roundabout near hoi fai road to a point about 150 metres south of its junction with lai cheung road will continue to be temporarily subjected to a speed limit of 50 kilometres per hour to facilitate the works of kcrc kowloon southern link

    止，連翔道南行線由其與近海輝道迴旋處交界以北約110米處起，至其與麗翔道交界以南約150米處止的路段，將繼續臨時實施每小時50公里的車速限制，以便進行九鐵九南線的工程。
  6. On 24 march 2006, the section of new clear water bay road from a point about 265 metres west of its second junction with the clear water bay road near good hope school to a point about 25 metres east of the same junction will be subject to a speed limit of 50 kilometres per hour

    10時起，新清水灣道由其與清水灣道的第2個交界處近德望學校以西約265米處起，至同一交界以
  7. As to project management of construction, the key to improve construction speed and shorten time limit for a project lie in rational disposition and utilize of resource ; factor influencing project quality a lot of, the key lie in the management of quality control point to construct course ; the most effective way of reduce expenses is raise working efficiency ; safety management as administrator is the attitude toward work and people in fact

    對施工項目管理而言，提高施工進度、縮短工期的關鍵在於資源的合理配置和利用；影響工程質量的因素很多，關鍵在於對施工過程中質量控制點的管理；節約成本的最有效途徑是提高工作效率；而安全管理實際上就是作為管理者，對工作、對人的態度問題。
  8. To tung chung eastern interchange from a point about 25 metres east of its junction with tung chung eastern interchange to a point about 155 metres east of the same junction will be subject to a speed limit of 110 kilometres per hour

    由北大嶼山公路西行通往東涌東交匯處的一段支路由其與東涌東交匯處交界以東約
分享友人
分享到 Line

分享到臉書