speed load coefficient 中文意思是什麼

speed load coefficient 解釋
速度載荷系數
  • speed : n 1 快，迅速。2 速率，速度。3 （汽車的）變速器，排擋。4 （膠片，照相紙）感光速度。5 〈古語〉興隆...
  • load : n 1 裝載，擔子；負擔；工作（負荷）量。2 （車船等的）裝載量；一馱，一車，一飛機。3 【電、機】（機...
  • coefficient : adj. 共同作用的。n. 1. 共同作用；協同因素。2. 【數，物】系數，率；程度。
  1. The thesis had done the theories analysis in detail and built the relevant mathematics models aiming at the mechanics characteristic about the lodging of stalk, the elastic and plastic deform of stalk under the action of the transverse loads, the mechanics condition which causes stalk pushed, the relation between the speed of unit and the surface radius of ski, the relevant location between the thickness of the compressed stalk and action location of load, the relevant location between the mating device and plough, the coefficient of overturning soil under the thickness of the compressed stalk and so on. in addition, the computer aided analysis and simulating experiments in field were acted by choice

    本文對秸稈自倒伏力學特性；橫向載荷作用下的莖稈彈塑性變形與秸稈被推倒的力學條件；機組作業速度與滑撬曲面半徑的關系；秸稈壓實厚度與加載作用點的相對位置；配套裝置與犁體相對位置；秸稈壓實厚度下的翻垡系數等，進行了較詳細的理論分析並建立了相關數學模型。在此基礎上，本項研究還選擇性地進行了計算機輔助分析和田間模擬試驗。
  2. ( 1 ) the dissertation theoretically analyses software direct compensating motor speed loss of open loop pump - control - motor speed governing system with inverter. the motor speed loss formula and compensating coefficient formula are given, and this provides the theoretic foundation for using software direct compensating method. the dissertation puts forward the control scheme of software direct compensating motor speed loss of open loop pump - control - motor speed governing system with inverter, and the method of " load sectionalization linear compensation "

    具體來說，本文的主要貢獻包括如下幾個部分： （ 1 ）對軟體直接補償開環變頻泵控馬達調速系統的馬達轉速降落進行了理論分析，給出了馬達轉速降落公式和補償系數公式，為軟體直接補償開環變頻泵控馬達調速系統的馬達轉速降落提供了理論依據；提出了變頻泵控馬達調速系統的負載補償控制方法和「負載分段線性補償」方法，由此提高了調速系統的速度剛性和調速精度。
  3. The theoretical analysis of large cryocondensation pump for nbi was mainly concerned. this paper emphasized on analyzing and calculating the heat load of cryocondensation pump, simulating thermal transmission coefficient and molecule transmission coefficient of radiation baffle according to monte carlo method, analyzing the process on cryo - surface and the factor of affecting pumping speed and hydrogen layer thickness of influencing cryo - parameter, etc. finally by verifying the pumping speed on large cryocondensation pump for neutral beam injection system, the pumping speed of 4. 0x105l / s ( for h2 ) was proven to be reasonable

    本文首先介紹了中性束注入系統的國內外發展狀況，闡述了中科院等離子體所ht - 7中性束注入系統的構成，主要對用於中性束注入系統的大型低溫冷凝泵的特性進行了理論分析；對冷凝抽氣面的熱負載進行了分析計算；用蒙特卡羅法對輻射擋板的分子傳輸幾率與熱傳輸幾率進行了模擬計算；研究了低溫表面的處理方法對抽速的影響以及氫層厚度對各低溫參數的影響；最後對用於中性束注入系統的大型低溫冷凝泵的抽速進行了驗證，得出的結論是：選取40萬升秒的抽速是合理的。
  4. 2, the friction coefficient at the pitch point is not a monotonic quantity of the rational speed or the load, instead of having a maximum value. and the value of the friction coefficient is very small, its order of magnitude only being 10 - 3. so, it is reasonable that the friction force on teeth surfaces are ignored when the gear - driven contact fatigue strength is designed

    2 、當輪齒在節點嚙合時，隨著轉速或載荷的變化，齒面摩擦系數並非呈單調變化，而是存在極值點;節點嚙合處的齒面摩擦系數很小，其數量級為10一， ，因此在做齒輪強度設計時，忽略齒面摩擦力的影響是有理論根據的。
  5. Owing to the interfacial cracking which occurs under higher applied load conditions, the composite with high content of tib _ 2 phase exhibited a transition from mild wear to severe wear over the applied load range from 10 n to 80 n. under moderate applied load, increasing the sliding speed caused a decrease in wear rate and friction coefficient of the in - situ composites because the formation of a protective oxide film occurred on the sliding surface and the hardness of the subsurface layer was maintained due to reinforcement of tib2 nanoparticles in the cu matrix

    隨著載荷的增加， cu -納米tib2原位復合材料的磨損率和摩擦系數增加；由於在較高載荷下發生表面開裂，高含量的tib2相增強原位復合材料發生了由輕度磨損向嚴重磨損形式的轉化。在中等載荷下由於表面保護性氧化膜的形成和基體中納米tib2相的存在使復合材料具有良好的抗軟化能力， cu -納米tib2原位復合材料的磨損率和摩擦系數隨著滑動速度的增加而下降。
分享友人
分享到 Line

分享到臉書