spin drying 中文意思是什麼
spin drying
解釋
離心烘燥-
Then the gel film can be prepared by dip - coating or spin - coating technique on the surface of glass and followed by drying in the ethanol vapor
使用浸漬提拉法或旋轉塗敷法，並通過放在乙醇蒸汽中乾燥，可在玻璃表面得到均勻的凝膠膜。 -
The dehydration time is square of the droplets diameter so the small diameters of the droplets can cut down the drying time then reduce the height of the drying chamber. to the combined spin - flow pressure spray drying, the diameters of droplets are small and the dehydration rate is higher so keeping the qualities of the dried products we can increase the speed of the inlet wind and reduce the temperature of the outlet wind thus can improve the evaporation intensity of the drying chamber and the average energy utilization of the drying equipment
因霧滴的脫水時間與其直徑的平方成正比，減小液滴直徑有利於縮短乾燥脫水時間，可有效降低乾燥塔的高度；由於旋流式組合壓力噴嘴霧化滴徑的減小，脫水速度明顯加快，在不影響乾燥物料性質的前提下，適當提高進風溫度，同時有效地降低排氣溫度，有利於提高幹燥塔的蒸發強度，也有利於提高幹燥設備的平均能源利用率。 -
( 2 ) base on the analysis of the atomizing principles of spray nozzle, mathematical model of combined spin - flow pressure spray drying was set up and the essential parameters such as spraying pressure, liquid quantity, temperature, spraying angle, inject distance, particle diameter and distribution, hollow diameter for several materials in normal conditions by experiment and ldv
（ 2 ）對旋流式組合壓力噴嘴噴射霧化機理加以分析，建立了旋流式噴嘴霧化的數學模型，採用冷態試驗法並藉助激光霧滴測試等實驗裝置對噴嘴的霧化參數（如霧化壓力、噴液量、料液溫度、霧化角、霧距、霧滴直徑和分佈以及噴嘴的空芯半徑等）進行測量和計算。 -
( 4 ) the droplets diameter of the combined spin - flow pressure spray drying are between 30um and 150um and the ranges of the droplets are narrow. the average diameter of the droplets is between 50 um and 100 um and the spraying angle can be adjusted from 30 to 180
（ 4 ）採用旋流式組合壓力噴嘴霧化后的液滴直徑大都分佈在30 150um之間，霧滴分佈范圍較窄，其霧化的平均液滴直徑在50 100um左右，壓力噴嘴的霧化角度可在150 180范圍內。 -
In this dissertation, the author summed up the muti - technique in fluid dynamics, heat and mass transferring, mechanical designing and computational technique and studied the conventional pressure spray dryers with different air disperse structure and outlet equipment, at last put forward the theme i. e. the study on combined spin - flow pressure spray drying technology, the main contents were as follows : ( 1 ) the combined spin - flow pressure nozzle was designed whose novel structure has no report at present, and the structural designing parameters were obtained through analyzing the physical characteristic of materials and distribution of particles
本文總結了國內外在壓力噴霧乾燥裝置的研究應用狀況，並分析了現有噴霧乾燥裝置設計方面的優缺點，運用流體力學、空氣動力學、傳熱傳質學、機械設計和計算機技術等多學科知識，綜合研究了傳統壓力噴霧乾燥系統的單噴嘴霧化裝置在併流、逆流以及混流乾燥中的應用和噴霧乾燥塔的不同布風裝置以及出風裝置的設置情況等，提出了新型旋流式組合壓力噴霧乾燥技術並對此進行了研究，其主要內容包括： （ 1 ）本文創造性地設計出旋流式組合壓力噴嘴的基本結構，並通過對料液的物化特性研究分析以及顆粒度的分佈要求，給出了噴嘴的不同結構設計參數。
分享友人