spline shaft 中文意思是什麼

spline shaft 解釋
花鍵軸
  • spline : n. 1. 【機械工程】花鍵；方栓；止轉楔；齒槽，齒條，鍵槽條。2. 【建築】塞縫片。3. 活動曲線規。vt. 1. 開鍵槽于。2. 用花鍵（或方栓）聯接。
  • shaft : n 1 箭；箭桿。2 （槍、槌、斧等的）柄；矛。3 【植物；植物學】稈；莖；柄。4 【動物；動物學】羽軸；...
  1. This article takes the lagrange equation as the principle, establishes mathematics modeling to the inertia brake vibration when it brakes, then simulates it with matlab. this paper educed the relation equations between, which are the inertia brake ' s friction coefficient of the brake ring and the friction disk, the mean radius, the braking force, rotation inertia of the driving top and the spline shaft, spiral climbing angle of the brake ' s concave - convex helicoid, the mean effort radius of the concave - convex helicoid, elasticity coefficient of the spring, quality of the driving top and the spline shaft, rotations inertia of the brake ' s rotation part besides the driving top and the spline shaft, suppresses sleeve. provides the theory basis for the inertia brake structure optimization

    本文以拉格朗日方程為理論基礎，對慣性制動器在制動時的振動進行數學建模，然後用matlab對其進行模擬，得出了慣性制動器在制動時振動角頻率分別與制動環和摩擦片之間的摩擦系數、制動力的平均半徑、主動頂和花鍵軸的轉動慣量、慣性制動器的凹凸螺旋面的螺旋升角、凹凸螺旋面平均作用力的半徑、彈簧的彈性系數、主動頂和花鍵軸的質量、慣性制動器除主動頂和花鍵軸外其他部分的轉動慣量和、頂壓套的質量等慣性制動器各零部件的物理參數之間的關系，為慣性制動器的結構優化提供了理論依據。
  2. For motor shafts, the highest stress is at the boundary between the key groove and the ring groove ; the next one is at bottom and terminal of the spline. according to the results, the 17. 4mm shaft is insecurity, the 22. 2mm and 30. 2mm shafts are security

    在軸的安全性上，對17 . 4mm泵軸計算結果是不安全的；對22 . 2mm泵軸計算結果是安全的；對30 . 2mm電機軸計算結果是安全的，而且還有較大的功率輸出空間。
  3. For the 30. 2mm shaft, there are still larger over measure to load. the strength is increased by optimization. for ? 17. 4mm shaft, the strength is increased by enlarge the inner dimension of the spline ; for 30. 2mm shaft, the strength is increased by adjust the structure at the boundary between the key groove and the ring groove, the highest stress of the shaft is at bottom and terminal of the spline after optimization

    其中對17 . 4mm泵軸的優化，通過增大花鍵內徑，提高了花鍵齒底的強度，降低了應力集中點附近的應力；對30 . 2mm電機軸的優化，通過在軸承鍵的環槽端增加倒角，有效降低了該位置的應力集中，使軸的最大應力點從軸承鍵與環槽的交界處轉變到花鍵根部與收尾的交界處，提高了電機軸整體結構強度的合理性。
  4. Numerical simulation of cold extrusion molding process of propeller shaft involute spline

    傳動軸漸開線花鍵冷擠壓成形過程數值模擬
  5. Spline shaft grinding machines - parameters

    花鍵軸磨床參數
  6. Spline shaft cold - striking machine

    花鍵軸冷打機床
  7. Spline shaft milling mahcine

    花鍵軸銑床
  8. The strength and fatigue analysis of spline shaft of hq1400 high pressure pump worm

    1400型壓裂泵蝸桿花鍵軸強度及壽命分析
  9. For pump shafts, the results reveal that the stress in the spline is higher than the other parts of the shaft, and the highest stress is at bottom and terminal of the spline. in fact, the broken of shafts is at the same position ; it demonstrates that the calculation is right

    實踐證明，軸斷部位基本集中在潛油泵軸花鍵的根部，說明計算結果和實際是吻合的；對于潛油電機軸，應力集中點主要處在軸承鍵與環槽的交界處和花鍵的根部。
  10. Various successive partial plastic forming methods for processing groove, including thread rolling, cross rolling and skew rolling, splitting, rolling of spline shaft, split rolling, open - die extrusion of spline shaft / gear, extrusion of internal screwed tooth socket parts with large helical pitch, integral cold forging for slot commutator, extrusion - ploughing for outside fin tube, drawing of tube with spiral internal / external ribs etc. have been introduced briefly

    摘要介紹了用於加工槽的各種連續局部塑性成形方法，包括螺紋軋制、橫軋與斜軋、分劈、花鍵軸滾軋、劈分軋制、花鍵軸齒輪開模擠壓、花鍵套擠壓、槽型換向器整體冷鍛、外翅片管擠壓一犁削、內外螺紋管拉拔等。
  11. The machine is suitabe for largebatch, small batch and single production of cylindrical spur and helical gears worm gears sprocket and spline shaft in certain range of parameters

    該機床適用於成批、小批及單件生產加工圓柱直齒輪、圓柱斜齒輪、蝸輪和一定參數的花鍵軸。
  12. We are the professional auto parts manufacturer, mainly working on driveline parts and electrical parts, including universal joint cardan, yoke, flange, spline shaft, and voltage regulator, fuel cut - off solenoid

    我們是一家專業的汽車零配件生產商，產品以汽車傳動部件和汽車電器部件為主，包括汽車萬向節十字軸、傳動軸叉、傳動軸法蘭、花鍵軸，以及汽車電壓調節器、油路開關等。
分享友人
分享到 Line

分享到臉書