standard tension 中文意思是什麼

standard tension 解釋
標準拉力
  • standard : n 1 標準，水準，規格，模範。2 旗；軍旗，隊旗；【徽章】標幟，標記；旗標，象徵。3 【植物；植物學】...
  • tension : n 1 拉緊；伸張。2 （精神、局勢等）緊張。3 【物理學】張力，拉力，牽力；（彈性體的）應力；（蒸氣等...
  1. Standard test method for interfacial tension of oil against water by the ring method

    採用環法測定油水界面張力的標準試驗方法
  2. Standard test methods for surface and interfacial tension of solutions of surface - active agents

    表面活性劑溶液的表面張力與界面張力的標準試驗方法
  3. Standard test method for torque - tension relationship of adhesives used on threaded fasteners lubricity

    螺紋緊固件用膠粘劑的轉矩拉力的標準試驗方法
  4. Standard test method for thick - adherend metal lap - shear joints for determination of the stress - strain behavior of adhesives in shear by tension loading

    拉伸載荷法測定剪切中膠粘劑應力-應變性能用厚被粘物金屬搭接-剪切接頭的標準試驗方法
  5. Standard test method for bond strength of adhesive systems used with concrete as measured by direct tension

    用直接拉力測量與混凝土一起使用的膠粘系統的粘合強度的標準試驗方法
  6. Standard practice for preparation and use of direct tension stress - corrosion test specimens

    直接拉伸應力腐蝕試樣的制備和使用
  7. Standard test method for tension - tension fatigue of polymer matrix composite materials

    聚合母體混合料拉伸疲勞度的標準試驗方法
  8. Standard practice for preparing tension test specimens for copper alloy sand, permanent mold, centrifugal, and continuous castings

    砂型鑄造硬模鑄造離心鑄造和連續鑄造銅合金鑄件抗拉試驗用試樣制備的標準實施規范
  9. Standard test method for wetting tension of polyethylene and polypropylene films

    聚乙烯和聚丙烯薄膜濕潤張力的標準試驗方法
  10. Standard test methods for structural panels in tension

    膠合板承受拉力的標準試驗方法
  11. Standard test method for creep properties of adhesives in shear by tension loading metal - to - metal

    用拉力負荷法測定金屬之間膠粘劑蠕變性能的標準試驗方法
  12. Standard test method for determining durability of adhesive joints stressed in shear by tension loading

    用拉力負荷法測定受剪切力的膠粘接合強度的標準試驗方法
  13. Standard test method for strength properties of adhesives in plywood type construction in shear by tension loading

    拉力負荷法測定膠合板結構中膠粘劑抗剪切強度特性的標準試驗方法
  14. Standard test method for apparent shear strength of single - lap - joint adhesively bonded metal specimens by tension loading metal - to - metal

    用拉力負載法測定單面搭接粘結的金屬試樣表面剪切強度的標準試驗方法
  15. Standard test method for performing tension tests on glass - fiber reinforced concrete bonding pads

    玻璃纖維增強混凝土焊接區的拉伸性能試驗的標準試驗方法
  16. The mechanical behaviour of a3 steel specimen under monotonic tension, pure torsion, torsion - tension, tension - torsion, torsion - tension - tension, tension - torsion - tension were studied by standard cylinder specimen in this paper

    本文研究了a3鋼試件在單一拉伸、純扭轉時的力學性能；在拉伸-扭轉、扭轉-拉伸時的力學性能；在扭轉-拉伸-拉伸、拉伸-扭轉-拉伸時的力學性能。
  17. Standard test method for strength properties of adhesives in two - ply wood construction in shear by tension loading

    用拉伸負荷法測定雙層膠合板結構中膠粘劑剪切強度特性的標準試驗方法
  18. Standard test method for strength properties of adhesives in shear by tension loading of single - lap - joint laminated assemblies

    用單面搭接迭層板裝配件的抗拉荷載法測定膠粘劑抗剪切強度的標準試驗方法
  19. Standard test method for determining strength of adhesively bonded rigid plastic lap - shear joints in shear by tension loading

    用抗拉荷載法在剪切膠粘劑粘接剛性塑料搭接接頭的抗剪切強度的標準試驗方法
  20. Standard test method of sharp - notch tension testing of high - strength sheet materials

    高強度薄板材料的銳切口張力試驗的標準試驗方法
分享友人
分享到 Line

分享到臉書