static pressure coefficient 中文意思是什麼

static pressure coefficient 解釋
靜壓系數
  • static : adj 1 靜止的，靜態的，靜力的。2 【物理學】天電的，靜電的。3 【無線電】靜態特性。4 固定的，不活潑...
  • pressure : n 1 壓；按；擠；榨。2 【物理學】壓力，壓強；大氣壓力；電壓。3 精神壓力，政治[經濟、輿論等]壓力。4...
  • coefficient : adj. 共同作用的。n. 1. 共同作用；協同因素。2. 【數，物】系數，率；程度。
  1. The way to get ko was given in this paper. by this way, the turbulence control equations were constructed from reynold equations with static pressure supposition and boussinesq ' s turbulence viscidity coefficient supposition and the salinity transportation equations, which are representative of the matter transportation equations, are given. the integrated deduction and corresponding boundary conditions are also given

    根據上述思想，從雷諾方程出發，採用靜壓假定和包辛內斯克的紊動粘性系數假說，建立了新坐標系中的紊流控制方程組，同時給出了對物質輸運過程具有代表性的鹽度輸運方程、相應的邊界條件及完整的推導過程。
  2. Using the system designed in this thesis work, flow field calibration of the wind tunnel is accomplished, which covers dynamic pressure drop coefficient, dynamic pressure time stability, axial static pressure gradient, boundary layer, and degree of turbulence, etc. boundary layer measuring principle and method are especially described in detail, the relationship between boundary layer thickness, wind speed setting, and the depth of the experimental section is summarized, and finally the calibration data for th e model center zone under specific wind speed are given

    然後利用本文設計的系統完成了落差系數、動壓時間穩定姓、軸向靜壓梯度、邊界層及湍流度等內容的流場校測。特別對邊界層測量的原理及方法做了較詳盡的敘述，總結出邊界層厚度與設定風速、實驗段深度的關系，然後給出模型中心區一定風速下校正數值。
  3. Taking the hydrostatic equilibrium of axial force of pump dm360 as the example, this paper elaborates design calculation and dynamic - static characteristic analysis of hydrostatic bearing with twisting plate throttle, derives design parameters and formulas of bearing structure, discusses effects of various main factors ( oil viscosity, compressibility, distortion coefficient of twisting plate, pressure of oil source, and bearing clearance ) on dynamic characteristic, and obtains some conclusions about the application of hydrostatic bearing in engineering practice

    本文以dm360型泵軸向力的液體靜壓支承平衡為例，對扭板節流靜壓支承的設計計算和動靜態特性分析進行了較為詳盡的闡述，推導出支承結構的設計參數和公式，討論了各種主要因素（油液的粘度、油液的可壓縮性、扭板變形系數、供油壓力、支承間隙）對支承動態特性的影響，給出了一些結論。
  4. Compare the reflection coefficient of each sample in front of breakwater 3. measure the pressure size of each sample inside of breakwater, and study its distribution and change law 4. separate the measuring pressure into the static and dynamic pressure, get the relationship between the static and dynamic pressure 5

    1 、比較各樣本之間的物理特性指標； 2 、比較各樣本之間的堤前反射系數； 3 、實測各樣本堤心內的壓強值，研究其分佈情況和變化規律4 、將實測壓強分解為靜壓和動壓，得出不同樣本間靜壓和動壓的大小關系。
分享友人
分享到 Line

分享到臉書