stator end 中文意思是什麼

stator end 解釋
定子端部
  • stator : n. 【電學】（固）定子；【航空】導向葉片壓氣機。
  • end : n 1 端，尖，末端，終點。2 邊緣；極點，極限。3 結局，結果。4 目的。5 最後，死。6 【紡織；印染】經...
  1. By starting with the analysis of generator end structure and overheat sources, it is presented that the technical key required to expand the capacity of the unit is to solve the electromagnetic leakage shielding problem. by proceeding with the analysis of the reasons causing the aging of the stator winding bars insulation, the necessity for stator winding bars to adopt class f insulation and relative fixing technological improvement are pointed out so as to extend the service life of the winding bars insulation

    從分析發電機端部結構及過熱原因入手，提出了增容的技術要點在於解決端部漏磁屏蔽問題；從發電機線棒絕緣老化原因分析入手，指出為延長定子線棒絕緣使用壽命，線棒主絕緣採用f級的必要性以及相關工藝的改進。
  2. The surface semi - conducting layer is widely used to control the electric field and suppress the surface corona discharge in both hv power cable termination and the end turns of hv generator stator winding

    摘要表面半導電層結構可以均勻電場和抑製表面電暈放電，因此被廣泛應用於高壓電力電纜接頭和高壓發電機定子線圈端部絕緣中。
  3. Against a prototype which is being produced ， its three dimension end region entity model of stator is established ， and with the aim of simplifying calculation ， the theory of how to simplify entity model is studied ， then the theory is made use of ， and the end region entity model of stator is simplifi - ed ； meshing characteristics of three dimension entity model and shortcomin - gs of end region entity model of stator are studied ， then meshing method of three dimension end region entity model of powerformer stator is studied as well ， and the simplified entity model is meshed with this meshed model ， the distribution of end region magnetic field of stator is analyzed ， and the magnetic field energy and reactance of powerformer end region are calculated and compared with design value because the prototype is being produced ， in this paper ， stator core ， gap and eddy equipment are not taken into consideration ， and this has a little influence on the result ， but through analysis ， the result is proved to be good through the example calculation ， it is known that the method of this paper is useful and through theoretic analysis ， it is proved that end region

    針對一臺生產中的樣機，對其建立了定子端部三維實體模型，而且為了達到簡化計算的目的，研究了如何將其簡化的理論，並應用這些理論對樣機定子端部實體模型進行了簡化；研究了三維實體模型的剖分特點和定子端部實體模型存在的缺點，在此基礎之上，研究了對簡化的powerformer定子端部三維實體模型的剖分方法，並且對簡化的實體模型進行了剖分。應用剖分的三維實體模型，用有限元法分析了powerformer定子端部的磁場分佈，計算了端部區域的磁場儲能，並利用磁場儲能計算了powerformer定子端部漏抗，將計算值與設計值進行了比較、分析。由於樣機處在設計生產階段，本文暫時沒有考慮定子鐵心、氣隙和渦流器件對端部磁場的影響，這對分析結果有一定的影響，但是仍然得到較好結果。
  4. In this paper ， the design characteristics and development situatution of powerformer are introduced ； the structure of prototype is studied ， and three dimension end region entity model of powerformer stator is established ； the theory of analyzing end region eddy magnetic field of stator by finite element method is studied ； end region magnetic field of stator is analyzed and the numerical value of end region leakage reactance of stator is calculated

    本文介紹了powerformer的設計特點和發展現狀；研究了其樣機本體結構，並建立了定子端部三維實體模型；研究了用有限元法分析定子端部渦流磁場的理論基礎；用有限元法分析了定子端部磁場並計算出了定子端部漏抗值。
  5. Therefore, the stable operational region of generators is discussed along with the analysis on relationship between under - excitation operation and loss of excitation / synchronism, end temperature rise of stator - core, and automatic excitation regulators etc

    針對這種情況，對發電機穩定運行區域進行了探討，並對進相運行與失磁失步、進相運行與定子鐵心端部過熱、進相運行與自動勵磁調節器等關系作了分析。
  6. Model test analyses and natural frequency measurement methods of large turbo - generators on stator end windings and evaluation criteria

    大型汽輪發電機定子端部繞組模態試驗分析和固有頻率測量方法及評定
  7. Measurement and evaluation of the dynamic characteristic on stator end windings of the large turbo - generator

    大型汽輪發電機定子繞組端部動態特性的測量及評定
  8. This thesis analyzes the retrofit of the end part electromagnetic shielding and the stator winding bars, i. e. the 2 technical measures taken for the purpose of expanding the capacity of 300 mw qsf - 300 - 2 type of turbine - generator

    本文分析了qsf - 300 - 2型300mw汽輪發電機增容改造採取的兩種技術手段：端部電磁屏蔽的改造和定子線棒的改造。
  9. The machine is suitable for forming up the small to medium size stator coil ; the operator put the on left side roller to form up inner side of coil, then put the stator on right side formiug mould to finally form up height, inner and outer side of coil to eusure the end product to meet the required specification

    本機適用於中小型定子的線圈整型，操作者只需將鉗入線圈后之定子置於左側滾輪上，先作內徑伸張整型，再將定子置於右側成型模上，作高度及內外徑之最終整型，即可達到所要求之尺寸。
分享友人
分享到 Line

分享到臉書