steam blowing 中文意思是什麼
steam blowing
解釋
下壓-
The article takes a 600mw natural cycle drum boiler ( soot blow using steam ) as investigating object, establishes soot accumulation loss and soot blowing energy loss models for its water cooling wall, superheater, economizer and air preheater respectively, set up instructions for soot blower operating. simulating calculation results are compared with site data to verify usefulness of key models. the article introduced the operation optimizing design of soot blowers of yanzhou no2 power plant based on theoretical research
本文以600mw汽包自然循環鍋爐（蒸汽吹灰）為具體分析對象，分別建立其水冷壁、過熱器、省煤器、空預器的積灰損失和各受熱面吹灰能量損失的模型，建立相應的吹灰器運行規則指導，對設計中的關鍵模型問題，通過模擬計算及與現場數據作比較的方法，驗證其可用程度。 -
The steam whistle is blowing.
汽笛在叫。 -
Transitional feature of the arc and metal droplet in the welding process with steam shielded arc is investigated by means of analysing the waveforms of welding voltage and current under different welding regimes and it is found that there are two types of arc process behavor ? " arc starting - arc blowing out - short - circuiting " and " arc - starting - short - circuiting ". under the condition of constant diameter of welding wire and its feeding speed, the arc process behavor can be changed by adjusting the inductance of welding circuit as well as the voltage of power supply. if arc process behaves as alternative process of " arc starting - arc blowing out - short - circuiting " with minimum time duration of arc blowing out and maximum frequency of short - circuit transition, the welding process will be stable with less spatter and smooth weld bead
通過分析不同焊接規范下的焊接電壓和電流的波形.研究了水蒸氣保護下電弧及熔滴過渡的特點，發現其電弧過程行為有「燃弧?熄弧?短路」和「燃弧?短路」兩種形式.在焊絲直徑和送絲速度一定的情況下，通過調節焊接迴路中的電感量和電源電壓，可以改變電弧的過程行為形式.若電弧過程呈「燃弧?熄弧?短路」交替進行，並且熄弧時間最短時，短路過渡頻率最高，在這種情況下，飛濺小，焊道成型好，焊接過程穩定 -
Abstract : the causes for low efficiency of the heater in no. 2 crude unit of jpc refinery are described and analyzed including water leaking of steam soot blower, dew point corrosion caused by steam, soot deposits in convection chamber owning to poor soot blowing, high flue gas temperature, no heat recovery of flue gas, and poor performance of insulation lining, etc. by using sonic soot removing system, flue gas recovery system, spray coating of fiber and rock wool, as well as adjustment of flow scheme accordingly in the technical revamping. the dew point corrosion is completely eliminated, the insulation performance is improved, the heat loss is reduced by 1. 25 %, the flue gas temperature is reduced to about 170, and the heater efficiency is increased from 83 % to more than 90 %
文摘:分析了金陵石油化工公司煉油廠二套常減壓裝置加熱爐存在的因蒸汽吹灰器漏水，蒸汽引起露點腐蝕及吹灰效果差造成對流室積灰，排煙溫度高，煙氣熱量未回收利用以及爐子保溫襯里效果差等問題，提出採用聲波除灰系統、煙氣回收系統、纖維噴塗和巖棉噴塗及相應的流程調整等改造措施.測定結果表明，本次技術改造解決了因蒸汽吹灰器漏水所造成的露點腐蝕問題，提高了保溫效果，減少散熱損失1 . 25 % ，排煙溫度降至170左右，裝置的爐效率由83 %左右提高到90 %以上 -
The causes for low efficiency of the heater in no. 2 crude unit of jpc refinery are described and analyzed including water leaking of steam soot blower, dew point corrosion caused by steam, soot deposits in convection chamber owning to poor soot blowing, high flue gas temperature, no heat recovery of flue gas, and poor performance of insulation lining, etc. by using sonic soot removing system, flue gas recovery system, spray coating of fiber and rock wool, as well as adjustment of flow scheme accordingly in the technical revamping. the dew point corrosion is completely eliminated, the insulation performance is improved, the heat loss is reduced by 1. 25 %, the flue gas temperature is reduced to about 170, and the heater efficiency is increased from 83 % to more than 90 %
分析了金陵石油化工公司煉油廠二套常減壓裝置加熱爐存在的因蒸汽吹灰器漏水，蒸汽引起露點腐蝕及吹灰效果差造成對流室積灰，排煙溫度高，煙氣熱量未回收利用以及爐子保溫襯里效果差等問題，提出採用聲波除灰系統、煙氣回收系統、纖維噴塗和巖棉噴塗及相應的流程調整等改造措施.測定結果表明，本次技術改造解決了因蒸汽吹灰器漏水所造成的露點腐蝕問題，提高了保溫效果，減少散熱損失1 . 25 % ，排煙溫度降至170左右，裝置的爐效率由83 %左右提高到90 %以上 -
For this, some measures have been put forward, including : strictly controlling metal temperature of turbine and boiler parts ; blowing out with steam ; suitably enhancing the speed of increasing or decreasing the load of unit ; carrying out aimed detection by using oxide skin detecting technology etc., to ensure the safety of operation
對此提出了嚴格控制蒸汽和鍋爐部件金屬溫度及嚴格進行蒸汽沖洗，適當提高機組升降負荷速度，並利用氧化皮檢測技術進行針對性檢測等措施，保證鍋爐運行安全。 -
When maria was blowing off steam, her husband would keep silent
每當瑪麗亞發牢騷時，她丈夫便沉默不語。
分享友人