steel ratio of concrete 中文意思是什麼
steel ratio of concrete
解釋
含鋼率-
Here the hsc of sompa is achieved through adding super - effective water reducer, fined slag and silicon fume, and decreasing the water / cement ratio. by varying the area ( spacing ) of tension bars, compressive bars, vertical links and distribution steel and embedding steel fiber and polypropylene fiber we try to improve the behaviors of reinforced high performance concrete one - way spanning slabs in bending, so that its ductility be greater than 5. with the same arrangement of steel the width of bending member is varied to observe the effect of the width / depth ratio on the ultimate compressive strain of concrete
通過變化受拉筋含筋率和受壓筋、箍筋（鉤筋、分佈筋）含量，或摻加纖維使之成為鋼纖維高強混凝土（ sfrhsc ）和聚丙烯纖維高強混凝土（ pfrhsc ） ，對高強混凝土雙筋截面梁、板的受彎性能進行了試驗研究，試圖改善高強混凝土受彎構件的延性，使其延性比大於5 ；並在相同配筋情況下，通過變化截面寬度，研究了高強混凝土受彎構件的寬高比對壓區混凝土極限應變的影響；並對試驗構件的裂縫發展情況進行了觀測。 -
This paper presents the structural design of the main bridge of lhasa river bridge, makes a deep - going study of the key techniques for design of the bridge, such as the reasonable span length ratio of each span of the 5 - span girder and arch hybrid structure, mechanical behaviour of the dual arch ribs, and section of the continuous girder tie beam, and also works out rigidity and stress conditions of the continuous girder tie beam and stress conditions of the concrete - filled steel tube arches of the main bridge
摘要介紹了拉薩河特大橋主橋結構設計情況，對於五跨梁拱組合橋梁各孔跨合理的跨度比、疊拱的受力行為及連續梁系桿截面形式等設計中的關鍵性問題進行了深入的研究，給出了主橋連續梁系桿的剛度和應力情況、鋼管混凝土拱的應力情況。 -
To meet the demands for large space and flexible compartmentation of buildings, laminated vierendeel trusses are adopted in high - position transfer story structures. first the bearing characteristics are analyzed, in which reasonable stiffness ratio of the upper chord, middle chord, and lower chord is derived. then combined with an actual engineering model ( 1 8 similar ratio ), the static loading and pseudo - dynamic tests of two models for laminated vierendeel truss used in transfer story structures are conducted, in which one model adopts reinforced concrete, and the other adopts prestressed concrete and shape steel concrete. seismic behaviors are analyzed, including inter - story displacement, base shear - displacement skeleton curves, and equivalent viscosity - damping curves. a program is programmed to carry out the elasto - plastic dynamic analysis, and displacement time - history curves of the two models are derived. the test and analysis results show that the laminated vierendeel truss with prestressed concrete and shape steel concrete has excellent seismic behaviors. it can solve the disadvantages of laminated vierendeel trusses used in transfer story structures. finally, some design suggestions are put forward, which can be referenced by similar engineering
為滿足建築物大空間和靈活隔斷要求，在高位轉換層結構中採用迭層空腹桁架結構.首先分析了其受力性能，得出了空腹桁架各構件合理的截面剛度以及布局形式.然後結合一實際工程，進行了兩榀迭層空腹桁架轉換結構模型（ 1 : 8相似比）的豎向荷載下靜力試驗以及擬動力試驗.其中一榀為普通混凝土迭層空腹桁架，另一榀配置了預應力和鋼骨混凝土，對比分析了兩模型的層間位移比、骨架曲線以及等效粘質阻力系數等抗震性能的比較，並進行了彈塑性動力分析.試驗和分析結果表明，配置預應力和型鋼混凝土的迭層空腹桁架轉換結構具有良好的抗震性能，可以成功地解決迭層空腹桁架作為轉換層結構所產生的弊端問題，最後對這類轉換層結構提出了相應的設計建議 -
Thecalculating results show that the composite action between concrete floor and steel beamsgreatly influence the bending bearing capacity and initial rotational stiffness of joints, it shouldbe considered in practical engineer. reinforcement ratio of lengthways reinforcing bar andthe stiffener of web have great influencer on the behavior of connections, while the thicknessof end - plate and degree of shear connection have a litter influence on its behavior
分析計算結果表明:樓板與鋼梁的組合作用對節點的抗彎承載力及初始轉動剛度的影響非常大，實際工程中節點設計應當考慮這種組合作用;樓板內縱向鋼筋配筋率與柱腹板加勁肋對節點性能影響顯著，而連接端板厚度及剪力連接程度的影響則不是太顯著。 -
The research shows that : 1 ) the ductility of the hsc bending members constructed is much greater than 5 ; 2 ) increasing the vertical links and distribution steel can increase the deflection under ultimate moment ; 3 ) with appropriate compressive bars, vertical links and distribution steel the increase of moment after yield and the decrease of moment under ultimate moment can be ignored, so the ductility of the hsc bending member is much larger ; 3 ) the width / depth ratio of hsc bending member has no obvious effect on the ultimate compressive strain of concrete ; 4 ) the method used here to calculate the deflection is applicable ; 5 ) the location of crack coincides with the location of vertical links and distribution steel ; 6 ) the bending property of the hsc structure under the blast load can meet the demand of protective engineering
研究表明：本文研究的梁、板構件的延性比遠大於5 ；增加箍筋（鉤筋、分佈筋）含量，可以提高壓區混凝土剝落時的撓度；在適當的受壓筋、箍筋（鉤筋、分佈筋）含量下，可以忽略壓區混凝土剝落瞬間的承載力下降，從而大大提高構件的延性；受彎構件的寬高比對壓區混凝土極限應變的影響不明顯；受彎構件的裂縫間距受箍筋（鉤筋、分佈筋）的布置影響；文中所用的承載力和變形計算方法是可行的。化爆試驗表明，高強混凝土構件的動載抗彎性能能夠滿足防護結構的要求。 -
Products function : put our “ sun shine ” brand carbon steel fiber evenly seep into concrete to form steel fiber reinforced concrete and it can decrease the thickness of reinforced concrete by half, it not only shorten the project time, save the material and manpower expense, bring distinct economic benefit, but also increase the performance of crack resistance, percussion resistance, tensile strength, bend resistance. scosspr resostamce amd wear resistance of the reinforced base materials. if the weight ratio of 2 % steel fiber seep into the concrete, it can solve the brittleness problem of the concrete, in the condition of 60 % ralative air humidity, after 21days air - dry, even 520 days air - dry, it ' s difficult to find any crack by eyesight, the bend resistance for the steel fiber concrete is 140 times stronger than the concrete without steel fiber, the capability of impact resistance increase 10 times
產品功能：將本公司「雙興」牌碳鋼纖維系列產品均勻地摻入混凝土中，形成鋼纖維增強混凝土，可使工程中鋼筋混凝土的施工厚度降低一半，不僅縮短了施工工期，節省了材料和人工費用，帶來顯著的經濟效益，且增強了基體的抗裂、抗沖擊、抗彎、抗剪、耐磨擦等性能，如摻入本公司2 %鋼纖維的混凝土，不僅解決了混凝土的脆性問題，在空氣相對濕度60 %的條件下風干21天後，甚至在風干520天，肉眼很難發現裂縫，摻入鋼纖維后的增強混凝土比不摻鋼纖維的混凝土抗彎強度提高140倍，耐沖擊荷載提高10倍。 -
Modify above model along with altering structural form or the constitution of the bridge, such as different standard, steel ratio, steel pipe diameter, concrete module, brace allocation, the length of concrete of the main ribs, suspending pole mode and cable local vibrations, calculate the variety of dynamic character, analyze this factors which will affect. 2
對斜拉拱橋自振特性進行參數分析，分別考慮了不同規范、含鋼率、拱肋鋼管直徑、混凝土彈性模量、橫撐布置、拱肋段混凝土長度、吊桿形式對自振特性的影響，最後考慮了斜拉索局部振動對自振特性的影響。 -
Fabrication of the box beam is divided into such parts as reinforcement, formwork, concreting, prestressing, moving and storing of beam, pipe grouting under pressure, end sealing of the beam, water - proof layer on the bridge surface system, protective coating etc. the paper makes description of effective box beam construction technology and workmanship which can be adopted in other projects, such technologies as : manufacturing and fixing of reinforcement, steel reinforcement fixing baseplate, web plate and top plate respectively and lifting the steel skeleton into form, requirements of design and manufacturing and way of utilization for dismantling - erection type formwork and hydraulic formwork, optimization of concrete ratio, concrete pouring process of two ends of beam in priority over the middle, in sequence of first baseplate followed by web plate and top plate at last, concrete pouring in inclined section and in horizontal layer, concrete vibration mainly by external vibrator in assistance with internal vibrator, methods and regulation for steam curing of concrete, dual controls over stress and strain to ensure quality of prestressing workmanship, construction method of effective beam moving by heavy - weight special moving facility, some regulations and key notes about construction of grouting under pressure, beam ends sealing, water - proof layer on the bridge surface system, protective coating
箱梁製造由鋼筋工程、模板工程、混凝土工程、預應力工程、移存梁工程、孔道壓漿工程、梁體封端工程、橋面防水層和保護層工程等施工環節組成。文中介紹的採用胎具製作和綁扎鋼筋，分底腹板和頂板分別綁扎並吊裝鋼筋骨架入模；拆裝式和液壓式兩種模板的設計、製作要求和使用方法；綜合考慮、優化混凝土配合比，混凝土灌注從兩端至中間、先底板、后腹板、再頂板的施工順序和斜向分段、腹板水平分層、附著式振搗為主、插入式搗固為輔的施工工藝，蒸汽養護的方法和規定；應力應變雙控制確保預應力施工質量的施工技術；採用重物移運器有效移梁的施工方法；壓漿、封端、橋面防水層和保護層施工的一些規定和注意事項等都是對箱梁製造行之有效的施工技術和施工方法，並可為以後類似施工作借鑒。 -
Based on the theoretical model, effects of influence of slenderness ratio, the changing steel ratio, strength of the steel and the concrete, load eccentricity ratio as well as pre - stress coefficient on the bearing capacity of the members considering influence of pre - stress in steel tube was discussed
分析了長細比、截面含鋼率、鋼材屈服強度、混凝土強度、荷載偏心率和初應力系數等因素的影響； 4提出了考慮鋼管初應力影響時鋼管混凝土構件承載力實用驗算公式。 -
Critical fatigue reinforcement ratio of concrete beams reinforced by cold - rolled deformed steel bar
冷軋帶肋鋼筋混凝土受彎構件的疲勞界限配筋率 -
Specimens ’ cracking load under dead - load, fatigue failure characteristic, fatigue life, deflection of span - centre, fatigue flexural rigidity, maximal crack width, development of cracks and strain of concrete and steel bars have been investigated. the influence of fatigue cycle characteristic, ratio of reinforcement, kinds of aggregate and concrete compressive strength on the specimens ’ fatigue behavior has been also investigated
對試件的靜載下開裂荷載、疲勞破壞特徵、疲勞壽命、疲勞荷載作用下的跨中撓度、截面疲勞抗彎剛度、裂縫開展情況及最大裂縫寬度、鋼筋及混凝土在循環荷載作用下應變等內容進行了研究，分析了疲勞循環特徵值、縱筋配筋率、骨料種類、混凝土抗壓強度等因素對試件疲勞性能的影響。 -
On the basic of former research men ' s experience, 18 experimental members ( including 9 simple beams and 9 restrained beams ) are designed and tested. in the experiment, phenomena are observed and record by taking photos in the whole process from the first crack appears to test members crash completely, experimental data is attained including load values of crack - appear load, critical load and terminal load, stress values of reinforcing steel bar stress, compressed concrete stress and beam flank stress and values of deflection etc. by analyzing the crack ' s appearing and developing form and stress values of concrete and steel bars, the crash modes of test beams are defined ; shearing force - deflection curves are contrasted and analyzed ; the effects on shear strength of the three factors as shear span ratio, concrete strength and restraining moment are also analyzed
借鑒已有試驗的經驗，本文設計和完成了對18根超高強混凝土無腹筋梁（包括9根簡支梁和9根約束梁）在集中荷載下抗剪強度的試驗，觀察了試件從裂縫出現到完全破壞失去承載能力全過程的試驗現象並通過拍照進行記錄，獲得了試件的斜裂縫出現荷載、臨界斜裂縫荷載和極限荷載等荷載值和縱筋應變、混凝土受壓應變和梁側混凝土應變等應變值以及撓度值等。 -
A reckoning model for the influences of steel ratio and concrete strength on different crack widths
含鋼率和砼強度對砼縫寬影響的計算模型 -
An analysis is developed for influence factors that have some influence on joints " behavior. the results show that axial ratio has a good and visible effect on the capacity of joints ; that the higher concrete strength is, the higher the capacity of joints is ; the ratio of reinforcements and the thickness steel web of column have large influence on the ductility src joints, not but the capacity of src joints
分析表明：軸壓比對節點的剛度、抗裂度的提高是有利的，且增大幅度較大；節點承載力和抗剪能力隨混凝土等級的提高而提高；鋼腹板厚度和配箍率的增大對節點承載力提高幅度不大，其對節點的延性影響較大。 -
Until now, the domestic and overseas scholar has studied the factors that have effect on performance of steel fiber reinforced concrete corbel such as shear span to depth, strength of concrete, reinforcement ratio ( including longitudinal reinforcement and stirrup ) and ratio of horizontal to vertical load. for calculating the cracking load, and ultimate load domestic and foreign scholar has brought forward a series of calculative formulas and methods have been put forward that based on statistical analysis, flexural model and truss model
到目前為止，國內外學者已研究了剪跨比、混凝土強度、配筋率（包括縱向鋼筋和箍筋） 、水平荷載與垂直荷載之比等因素對鋼筋鋼纖維混凝土牛腿受力性能的影響，對牛腿的抗裂計算和承載力的計算，國內外學者曾提出了基於數理統計分析、彎壓模型和桁架模型等的一系列計算方法和計算公式。 -
Discussion on limit value of axial compression ratio of steel reinforced concrete columns
鋼骨混凝土柱軸壓比限值控制的討論 -
In order to determine the relations between the four main bond - anchoring factors - concrete strength, concrete cover thickness, steel shape embedment length and the ratio of the transverse hoops - and the bond strength, and establish the bond - slip constitutive relations, 16 standard push - out test specimens were designed, and 4 comparison specimens were additionally designed to find the difference of the bond performance between the web, inside and outside of flanges the steel shape
設計了16個型鋼混凝土標準推出試件，以考察混凝土強度、型鋼的混凝土保護層厚度、型鋼埋置長度及橫向配箍率四個主要錨固條件與粘結強度的相互關系和型鋼混凝土粘結滑移本構關系；設計了4個對比試件，以考察型鋼翼緣內側、外側和腹板與混凝土粘結性能的區別。 -
Considering the characteristics of internal force and structures of simply supported pc bridges, a novel automatically step - up method ( asum ), taking into account the influence of steel arrangement, steel ratio, stress losses of tendons and time - dependent concrete modulus, to analyze creep and shrinkage effects is presented. this method accepts all kinds of expressions of creep and shrinkage, and it is easy to calculate total stress, strain of concrete and steel and deflection of bridge at any time, the expected prediction accuracy will be obtained by further dividing the time - step within duration
首先，針對預應力混凝土簡支梁橋的受力特徵和構造特點，提出了徐變效應分析的全量形式自動遞進法，可考慮截面上鋼筋位置、配筋率、預應力鋼筋鬆弛、混凝土彈性模量隨時間變化等影響，且計算式可適用於任何形式的收縮、徐變特性表達式；建立的公式可方便地求解任意時刻混凝土、鋼筋的應力與應變和跨中梁體的豎向變形，計算精度可方便地通過計算時段的細分來控制，直至給出滿意的結果。 -
( 4 ) influences of parameters on the behavior of the moment ( m ) versus curvature ( ) response, and the lateral load ( p ) versus lateral displacement ( ? ) relationship such as fire duration time, axial load level, slenderness ratio, steel ratio, steel yielded strength and concrete
（ 4 ）對影響彎矩-曲率（ m - ） 、荷載-變形（ p - ）滯回曲線骨架線的各種因素，如受火時間、軸壓比、長細比、含鋼率、鋼材及混凝土強度等參數進行了分析。 -
Fifty concrete filled thin - walled steel tubular stub columns were axially tested, where diameter ( width ) to thickness ratio was selected as the main varied parameter. the behaviour of concrete filled thin - walled steel tubular stub column was analyzed, and the simplified calculation method of bearing capacity was discussed. based on the current test results and those reported in the literature, the upper limits of d / t and b / t of cfst members were recommended
以截面徑（寬）厚比為基本參數，進行了50個薄壁鋼管混凝土軸壓力學性能的實驗研究，考察了薄壁鋼管混凝土的軸壓力學性能，並對其軸壓強度的計算方法進行了探討，基於本文和其他研究者的實驗結果，建議了鋼管混凝土構件截面合理的徑（寬）厚比限值。
分享友人