steeve 中文意思是什麼

steeve 解釋
n. 名詞 1. 【造船】斜艏桅仰角。
2. 起重桿；吊桿。
vt. 及物動詞 1. 用起重桅裝貨。
2. 使（斜艏桅）傾斜。
vi. 不及物動詞 （艏斜桅）傾斜。

  1. As a brand new supporting structure, the steeve - arch was firstly used in the design of tangyu aqueduct ( also used as a bridge ) lies on the eastern main ditch of shitou river, shaanxi province

    吊桿式拱架作為一種新型拱式支承結構在陜西省石頭河東乾渠湯峪渡槽（橋渡結合工程）設計中首創應用。
  2. The name stephenson or stevenson is said to signify, in the norse tongue, the son of steeve, or the strong ; and certainly the subject of this story exhibited, in a remarkable manner, the characteristic quality of his family

    斯蒂芬森或斯蒂文森姓氏據說在挪威語中意味著「英勇之子」 ，當然，本傳記的主題就是以一種獨特的方式展示這一家族獨具特色的意志品德。
  3. 3, the comparing analyses of tech - economic features, anti - seismic features on transverse direction of the aqueduct 1 ) from the angle of engineering cost, steeve - arch supporting structure, whose down beam have tectonic cracks, can spend less money up to 90 % or more than the usual arch supporting structure, namely steeve - arch supporting structure is very obvious on the side of cost

    3 、技術經濟比較分析1 ）從造價方面看，下弦桿分縫的吊桿式拱架結構相對于下弦桿構造不分縫的豎桿式拱架結構可節約工程造價達到90以上，吊桿拱的經濟效果十分明顯。
  4. 2 ) from the angle of constructing course, steeve - arch supporting structure requires low - capacity cranes to erect, and simple constructing methods easy to meet. the time spending on construction is short. the usual arch supporting structure requires high - capacity cranes to erect, and complicate constructing methods hard to meet

    2 ）從施工角度看，吊桿式拱架支承結構對吊車的起吊能力要求低，工藝簡單，施工方便，工期短；豎桿式拱架支承結構起頂重量大，對吊車的起吊能力要求高，施工難度大。
  5. 2 ) the structure elements should be laid out symmetrically and uniformly when designing steeve - arch structure, what ' s more, the reasonable selection of section geometric size near the arch foots of first beams is paid attention to and the arrangement difficulties of steel bar due to the big eccentric pressures 2, the analyses of anti - seismic features on transverse direction of the aqueduct l ) the method of adjusting the elements " mass can be harnessed in order to even the layout of seismic loads

    2 ）設計吊桿式拱架支承結構時，各部分構件應當均勻對稱布置。另外，還應注意頭道梁拱腳附近截面的尺寸擬定，克服地震內力造成的大偏心受壓狀態給結構配筋設計增加的困難。 2 、橫槽向抗震性能分析1 ）可利用調整構件質量的方法，使得結構的某些構件的地震荷載分佈均勻一些。
分享友人
分享到 Line

分享到臉書