structural ring 中文意思是什麼

structural ring 解釋
環形隔框
  • structural : adj. 構造上的，結構上的，組織上的。adv. -ly
  • ring : n 1 圈，環，輪；戒指，指環，耳環，鼻圈，鐲子（等）；【運】吊環。2 輪狀物；【植物；植物學】年輪；...
  1. Tooth profiles and structural characteristic of ring gear of epicyclic drive with eccentric wheel and push rod

    偏心輪推桿行星傳動內齒圈齒廓及其結構特性研究
  2. Being lacking of understanding of behaviors of circular working shaft, the paper proposed theory about ring - beam ' s load - distribution calculations and analyzed the structural behavior of circular working shaft ( cws ) by the numbers from the standpoint of properties of structural style and stress incorporated with thoughts of shared load introduced to research of cws. first, regarding cws as structure of series of hypothetic horizontal circular rings and vertical beams, and considering cws ' s formation and development, the paper proposed load - distribution thoughts to solve cws ' s calculations. ring - beam calculation theory was put up and software cbtlmp1. 0 was worked out based on the conditions of external applied load shared by rings and beams, and of deformation conformity

    首先，本文提出用分載思想解決圓形工作井結構的計算分析問題，將圓形工作井結構看成是由一系列的假想的水平圓環和豎直梁組成的結構，考慮工作井形成過程及形成階段與項進階段的連續性，根據某一時刻相對于上一時刻外載增量由環與梁分擔、環與梁在交叉處變位增量一致的條件將環計算理論與梁計算理論結合起來，據此建立了環?梁分載計算理論並研製了環?梁分載計算分析軟體cbtlmpv1 . 0 。
  3. With this purpose, this paper researches the state of dometic and overseas seal technique ; uses other enterprise ' s successful experiments for reference ; combines the factory set ' s structural property, technics characteristic and the different request of medium leakage degree ; considers the respective strongpoints of floating ring seal, conical floating seal, suction labyrinth seal, inflator labyrinth seal, mechanical seal, dry gas seal ; finds out the optimum, dependable seal techinique fiting for each set on the base of entire analysis on the centrifugal compressor. and in the end by putting this plan into practice the factory achieves localized reconstructs, reduces the production cost and fulfils the demands of secular safe use

    本文在把握國內外離心壓縮機密封技術的發展狀況，借鑒其他企業的成功經驗基礎上，根據我廠機組結構特性、工藝特性、介質泄漏程度要求的不同，以及浮環密封、錐形浮環密封、抽充氣式迷宮密封、機械密封、干氣密封的各自特點，對離心壓縮機存在的密封問題進行了全面剖析，研究了適合每臺機組最佳、可靠的密封技術，實施了本地化技術改造，降低了生產成本，滿足了機組長期穩定運行的生產要求，取得了顯著的經濟效益和社會效益。
  4. 4. the feature of linearity and ring structures shows that three structural lenses that are formed by the junction of four level i faults in alignment are helpful to the formation of ore - body. in longshujiao and longtouzhai lenes there are many intersectant east - north and west - north low level faults, so they are concentration place of ore - bodys

    4 、從遙感線環構造特徵上看，區內的四條主要東西向線性構造，是級控巖控礦線性構造，它們在走向上弧形交接形成三個構造透鏡體，是成礦的有利部位。
  5. We rounded analysis that ring stator ’ size parameter how to affect ring stator ’ characteristic frequency by use the software for numeric analysis, and afford theoretical foundation for the optimum design of ultrasonic motor ’ structural parameter

    本文還利用分析軟體，全面地分析了定子圓環各個尺寸參數對特徵頻率的影響，為超聲波電機結構參數的優化設計提供了理論依據。
  6. In time of use of this product, it is only required to make hanging rope cross above solid structural object with truncated edge, hang ring - shaped hook on hanging rope inside the upper interface and circular ring of anti - dropping device, and then hang the ring - shaped hook of roll - up safety belt inside the semi - circle ring on safety belt

    使用時只需將懸掛繩跨過上方堅固鈍邊的結構物上，將懸掛繩上的環形鉤掛入防墜器的上部介面和圓環，將卷收安全帶的環形鉤掛入安全帶上的半圓環內即可使用。
  7. 9 series pressure cavity is made of stainless steel single unit integration structure by processing so may guarantee for the better seal performance. the characteristic of product are no o - ring, no welded, no silicon oil or other organic, structural durability ; the most apply to pump and compressor, liquid pressure and pneumatic system, go - anywhere vehicle, energy and water processing system, pressure instrument, refrigerating equipment, agricultural machinery device, locomotive braking system

    9系列壓力腔採用不銹鋼單件一體式結構加工而成，因而可以保證較好的密封性能， 9系列產品的特點是無o形圈無焊縫無硅油或其它的有機物，經久耐用，主要應用於泵及壓縮機，液壓及氣動系統越野車能源及水處理系統壓力儀表冷凍設備農機設備機車剎車系統。
  8. The control of the deep - seated structural - magmatic process over the metallogenic system around the middle - lower yangtze river reaches is shown as : ( 1 ) the mantle uplift belt is closely related to the general geological background of the metallogenic system ; ( 2 ) the primitive magma originated from different parts of the mantle uplift belt ( mantle ridge or mantle slope ) shows differences in style of formation and composition and results in different magmatic series and metallogenic subzones, respectively ; ( 3 ) the varying depths of structural - magmatic chambers may form a " three - layered structure " ( central type, network - like and ring - like ) and this is the primary factor that controls the different magmatic series and the concerned cluster of ore deposits ; ( 4 ) the alkaline basaltic magma derived from the mantle ridge forms high - potassium and calcium alkaline magma and shoshonitic magma due to its altering intensity of afc process with the lower crustal material, which has something to do with the copper - gold and iron - sulphur metallogenic subsystems, respectively

    深部構造巖漿作用對長江中下游成礦帶安徽沿江地區成礦系統的控製表現為： （ 1 ）地幔隆起帶與成礦系統的總體地質背景的演變密切相關； （ 2 ）源於地幔隆起帶不同部位（幔脊與幔坡）的原始巖漿，其生成方式和物質組成不盡相同，它們分別產生相應的不同巖漿巖系列和成礦亞帶； （ 3 ）不同深度的構造巖漿房組成中心式網格式環帶式「三層結構」 ，是控制區內不同巖漿巖系列及有關礦床集中分佈的主要因素； （ 4 ）源於地幔隆起帶脊部的堿性玄武巖漿，由於與下地殼物質發生的afc作用強度不同，形成了高鉀鈣堿性巖漿和橄欖安粗巖漿，分別與銅、金成礦亞系統和鐵、硫成礦亞系統有關。
  9. The structural design and application for combination between the helical axial seal and floating - ring seal have been performed

    實現了螺旋密封與浮環密封相結合的結構設計及應用。
  10. The cysteine polypeptide ring formed by them is called type - ii construction domain. now the type - fl construction domain is considered as the structural basis of multiple functions of bsp protein

    在每個疏水區中半胱氨酸殘基是按1 ? 3和2 ? 4順序形成二硫鍵，這樣構成的胱氨酸多肽環被稱作型結構，目前認為型結構是bsp蛋白多種功能的結構基礎。
分享友人
分享到 Line

分享到臉書