surface equation 中文意思是什麼

surface equation 解釋
表面方程
  • surface : n 1 表面；地面；水面；廣場，空地。2 外觀，外表，皮毛。3 【幾】面；切口；【航空】翼面。adj 表面的...
  • equation : n. 1. 平衡，均衡；平均，相等。2. 【數學】方程式，等式。3. 【天文學】（時）差；均分，等分。4. 【化學】反應式。
  1. The paper studies the surface geometry of globoidal indexing cam by applying the theory of conjugate surfaces and the method of coordinate transformation, presents the equations related to the main inducement curvature of the cam profiles, analysis and deduces the equations of two circumscription curves, which judge if the conjugate surface could mesh properly. some calculate examples and conclusion are given. the surface equation of the globoidal cam and conjugate equation are established

    論文首先在分析空間嚙合原理基礎上，採用坐標變換法推導出弧面分度凸輪的工作廓面方程、嚙合方程和壓力角計算公式，對弧面分度凸輪的嚙合特性進行了深入的分析和研究，對判斷曲面能否正確嚙合的依據如兩類界限線方程以及誘導主曲率等進行推導，並給出算例。
  2. Based on the geometry characteristics of bertrand surfaces, the complicated surface conjugation issue can be discussed with their directrix line. according to the different generatrix line which can be divided into common plane curve, circular - arc curve and straight line, bertrand conjugation surfaces are parted into three typical types, and the basic equation and differential formula are established, then the conjugation conditions are found. aiming at the inclusive problem, the structure condition is given

    論文將白川德共軛按母線為一般平面曲線、圓弧、直線分為三種典型類型，分別建立了共軛的基本方程與微分關系式，據此給出了各種類型的共軛基本條件，發現這是一類更強更嚴的條件，存在有相容問題，進而研究了白川德共軛的結構條件，至此確立了白川德共軛的基本框架。
  3. As we know, inverse techniques make blade ' s profile well compatible with its surface velocity distribution, however, they give designers big challenges that the ideal velocity distribution is hard to obtained and sometimes the non - physical solution, such as double covering of flow field or unclosed profiles, would come out. the proposed design procedure in the paper has avoided the disadvantage mentioned above. in this paper, a quasi - irrotational equation is used to describe the flow in cascade instead of the generally used irrotational equation

    眾所周知，一般的反問題和混合問題的最大特點，是在給定的壓力面和吸力面上的壓力分佈或速度分佈條件下，直接得到葉片的幾何形狀，它可以使葉型型面與表面氣流參數有機結起來；其不足之處在於，對設計者而言，很難給定理想的葉片表面壓力分佈或速度分佈，並且有時會得到一個非物理解，如：得出的初始葉型可能會出現前緣、尾緣不封閉的現象。
  4. A one - dimensional oceanic mixed layer model with the m - y level - 2. 5 turbulence closure schemes is employed. the rate of energy loss by breaking waves is estimated by parameterization and incorporated into the model as a source of turbulence kinetic energy ( tke ) by modifying the existing surface boundary condition of tke equation. the velocity field and turbulence energy budget are calculated under different forcing conditions ( the results given below are for a wind speed of 20 m / s. )

    採用一維2 . 5階湍封閉混合層模式，根據參數化方法對波浪破碎導致的能量耗散率進行了估計，通過改變湍動能方程的上邊界條件引入波浪破碎對湍動能生成的影響，計算了不同風應力強迫下的混合層流場結構和湍能量收支（下述給出的結果是取風速為20m s得到的） 。
  5. Formula to evaluate translation of the tooth - surface and the equation to describe the generatrix of the negatively cambered sooth - surface were derived, respectively

    分別推導得到齒面平移距離和內凹齒面母線方程的計算公式。
  6. The boundary condition at bed surface of diffusion equation of nonuniform sediment is derived based on the concept of exchange intensity of stochastic theory by the author

    摘要文中首先給出了由我們建立的床面泥沙交換理論導出的非均勻沙擴散方程的邊界條件。
  7. Abstract : the shaping equation of steamed bread in circular trough camber of shaping roller, the instantaneous velocity of its surface, and the strength by shaping roller were analyzed during shaping, then a theory base for the design of steamed bread shaping machine was provided

    文摘:分析了饅頭成型過程中成型輥上圓弧槽曲面內饅頭生坯的運動方程，饅頭表面動點瞬時速度及饅頭成型時受力分析，為饅頭成型機的設計提供了理論依據。
  8. Aiming at the existence of coal dust and gas in the coalmine environment and the special requirements of mine case explosion - proof surface process, the error conversion model, shape precision characteristics, transfer drawings, descriptive equation and error transfer structure chart in the production technological process of case accessories adopting the information flowchart of control theory are discussed, which simplify the traditional block diagram of technological process and represent the relationship of working procedure ( variable ) by information flowchart instead of miscellaneous block diagram

    針對煤礦井下煤塵和瓦斯存在的環境特性、煤礦井用箱體防爆面加工的特殊要求，採用控制理論的信息流圖，對工藝過程中傳統方塊圖進行簡化，使繁雜的方塊圖解採用信息流圖表示工藝過程的工序（變量）之間關系。
  9. The wave - equation - datuming ( wed ) technique is a necessary alternative to the conventional static corrections when the surface - consistent assumption is invalid

    摘要波動方程基準面校正處理被認為是當地表高程變化劇烈、地表一致性假設又不成立的情況下對于常規高程基準面校正的必要替代。
  10. New numerical method to solve eigenvalue equation of surface wave

    計算表面波特徵方程的一種新的數值方法
  11. The equation for estimating land surface temperature of huaihe river basin has been set up by using the data of split window channels of trmm and gms - 5 satellite and the ground observation data of hubex

    利用trmm衛星和gms - 5衛星的兩個紅外分裂窗通道的亮溫資料，結合淮河流域能量與水分試驗hubex加密觀測期間獲得的地面溫度的觀測資料，建立了反演淮河流域地面溫度的參數化方程。
  12. The studies on flocculation parameters of high turbidity water are completed more integrally, including establishing the equation about the relationship between the covering ratio of flocculent on silt surface 6 and the surface area of silt particles s. the re - concentration law of thickener underflow is studies

    建立了一定沉速下，泥沙固體顆粒表面覆蓋率與泥沙顆粒表面積s間的函數關系式；較系統地完成了高濁度水絮凝參數的研究。研究了高濁度水沉澱池排泥的再濃縮規律。
  13. ( 2 ) intersectioning algorithm of nurbs surface and general implicit surface is researched in which the parametric formula are substituted into the implicit surface equation and then get the nonlinear two - dimensional equation on parametric domain

    （ 2 ）實現了nurbs參數曲面與廣義的隱式曲面的求交演算法並將其應用於船體曲面與水線面的求交中。
  14. From the aspect of geometry, structure design, manufacture and examine, this paper generally summarizes the gcm ' s study progress in detail, discusses its kinetic rule and the determination of its primary structure parameter, and educes its surface equation and pressure angle equation based on the homogeneous matrix transformation and the conjugate engagement theory of spatial surface. on the basis of geometry study of gcm, the paper makes a comprehensive analysis to the interference phenomenon that will possible exist in the assemble course of two different structure of gcm with the help of matlab software

    本文從運動幾何學、結構設計、動力學、製造和檢測等方面對國內外弧面凸輪機構的研究進展進行了全面綜述，詳細論述了高速凸輪機構的運動規律和弧面凸輪機構基本尺寸的確定，基於空間曲面共軛嚙合原理，通過齊次變換推導了外弧面凸輪的曲面方程和壓力角方程，並提出了對應的廓面修形演算法；提出了內弧面凸輪機構的構想，推導了內弧面凸輪的曲面方程和壓力角方程。
  15. Finally, by means of comparing the theoretical tooth surface equation with the tooth surface equation included errors of cutter position and cutter position angle, the quantitative analysis of the theoretical tooth shape and the tooth shape considering the errors of cutter position and cutter position angle was curried out based on the software above. from which, the effect of errors of cutter position as well as cutter position angle on the processed tooth shape and transmitting behavior of this kind of gearing was studied

    最後，通過比較雙圓弧弧齒錐齒輪齒面理論方程與加入刀位及刀位角誤差后的齒面方程，應用上述軟體和通過進一步的數值計算，進行了無誤差的理論齒形與加入刀位及刀位角誤差后所得到的實際齒形之間的定量分析，比較直觀、方便、準確地對刀位及刀位角誤差對雙圓弧弧齒錐齒輪的齒形以及傳動的影響進行了初步研究。
  16. In this dissertation, first, based on the theory of w - n gearing, characteristic of tooth profile as well as the processing principle of helical bevel gear, a cutting meshing analysis about double circular arc profile bevel gear was carried out, the equation of meshing in the process of cutting tooth, the surface equation of generating gear as well as the general tooth surface equation of double circular arc profile bevel gear were obtained

    本論文首先根據雙圓弧齒輪傳動的嚙合理論，結合其齒形特點和弧齒錐齒輪的加工原理，進行了雙圓弧弧齒錐齒輪的切齒嚙合分析，得到了切齒嚙合過程中的嚙合方程、產形輪齒面方程以及雙圓弧弧齒錐齒輪的通用齒面方程，為下一步生成雙圓弧弧齒錐齒輪的三維模型打下了基礎。
  17. Jacobi transformation is used to find correlations among coefficients. then a method to transform general quadratic surface to formal quadratic surface equation is introduced. the location, direction and size of quadratic surface are obtained

    論述了運用jacobi變換方法來處理系數相關性問題，實現了二次曲面的一般方程的求取，並探討了將通用系數形式轉化為標準二次曲面方程的方法，從而求得二次曲面在空間的位置、方向和大小。
  18. Taking the meshing theory of conjugate curved surface as a foundation, utilizing array method of rotation transformation of vector, the meshing equation and contour surface equation of conical cam mechanism with swinging conical roller follower were analyzed and derived, and the calculation formula of pressure angle and synthetic curvature of the mechanism was presented, thus laid a solid theoretical foundation for enhancing the machining accuracy of conical cam, improving its processing method and achieved the integration of cam cad / cam

    摘要以共軛曲面嚙合理論為基礎，運用矢量的旋轉變換矩陣法，分析並推導了圓錐滾子擺動從動件圓錐凸輪機構的嚙合方程和廓面方程，並給出了機構的壓力角和綜合曲率的計算公式，為圓錐凸輪加工精度的提高，改進其加工方法，實現凸輪cad / cam一體化奠定了堅實的理論基礎。
  19. Given a response surface equation in quadratic form, the six sigma black belt will be able to compute the stationary point

    給出一個二次方程式形式的響應曲面公式， 6西格瑪黑帶應能計算出駐點。
  20. Simultaneity it can generate the three - dimensional model of corresponding gear in a minute after by directly inputting gear parameters and the parameters of tooth form, which could prove th at the general tooth surface equation of double circular arc profile bevel gear obtained above was correct

    同時也可直接輸入齒輪參數和齒形參數，來生成相應齒輪的三維模型，從而證明了前面推導的雙圓弧弧齒錐齒輪通用齒面方程式的正確性。
分享友人
分享到 Line

分享到臉書