surface specific heat 中文意思是什麼
surface specific heat
解釋
表面比熱-
And the effects of ballmilling, floatation and weight - selection, acid treatment and heat treatment on the specific surface and adsorbability of the natural minerals have been studied further, especially on diatomite and sepiolite
並進一步研究了球磨、浮選和重選、酸處理、熱處理等前處理對天然礦物的比表面和吸附性的影響，並著重討論了前處理條件對硅藻土和海泡石的吸附性能的影響。 -
The calculation program using the matlab has been worked out to get the numerical solutions of the proposed models. the experiment has first been conducted in the laboratory to get the fundamentals thermal and moisture properties ( such as materials density, specific heat capacity and thermal conductivity ) and also the material moisture absorption isotherms of adobe building materials. the methods of measuring the surface mass transfer coefficient and material moisture content have been proposed
首次對生土建築材料物性參數進行了實驗測試，得到了常用生土建築材料的密度、比熱和導熱系數等參數值，得到了生土建築圍護結構的等溫吸濕平衡曲線的擬合函數關系式；此外，研究了生土建築圍護結構表面質交換系數實驗測定方法，探索了利用電阻率測量生土建築圍護的安窪築科技人學博十學位論文結構內部含濕量的測試方法。 -
In this paper tio2 / minerals have been prepared using natural minerals as carrier and the industrial metatitanic acid and the industrial sulfate titanium liquid as the raw material based on the effects such as loading capacity of tio2, specific surface area of minerals, different mineral source and preparation cost. the acid treatment and heat treatment of minerals, preparation methods and condition of ticvminerals have been studied, the photocatalytic experiments on samples were tested from degrading methylene blue solution, and some important results as follows : 1
本研究以天然礦物對tio _ 2的負載能力、比表面積、礦物來源、材料成本等因素為依據，通過對天然礦石載體的活化工藝研究和工業偏鈦酸、工業硫酸鈦液（以下簡稱濃鈦液）為原料制取tio _ 2天然礦物復合材料的制備工藝研究，以及樣品光催化降解有機物的研究，最終制得了具有光催化活性的tio _ 2天然礦物復合材料。 -
And the value drop to the lowest at ph = 0. 8. as the increase of heat treatment temperature, the pore size distribution peak of sio2 microspheres is very narrow, meanwhile the specific surface area is the smallest before 160 c. the polymer template is removed at 350 c, so the pore structure of sio2 particles has a big change which involve the increase of specific surface area and the broaden of pore size distribution peak. with the continuous raise of temperature the sio2 network will shrink little, as a result the average pore size will decrease, but the specific surface area has no obvious change
結果發現：二氧化硅膠體顆粒均勻分佈於脲醛聚合物網路中，煅燒去除有機模板后微球表面變粗糙，而粒徑沒有明顯變化； ph值較小時，復合微球中聚合物含量較大，而ph值較大時，得到復合微球結構鬆散，因此熱處理后的二氧化硅微球孔容及平均孔徑都較大，而在ph = 0 . 8時，得到最小值；武漢理工大學碩士學位論文隨著熱處理溫度的變化，小於160時，空分佈較窄，而比表面積較小，在350時，由於有機模板的去除，微球孔結構發生突變，比表面積明顯增大，而孔徑分佈變寬，溫度繼續升高時，二氧化硅網路發生收縮，平均孔徑變小而比表面積由於有機炭化物的完全去除沒有太大變化;微球中的微孔在熱處理過程中處于平衡狀態，分佈沒有太大變化。
分享友人