surveying calculation 中文意思是什麼

surveying calculation 解釋
測量計算
  • surveying : n. 測量（學、術），勘測。 a surveying reporter 測量員。 a surveying ship 測量艦。
  • calculation : n. 1. 計算，計演算法。2. 推定，預測。3. 深思熟慮，精打細算；慎重的計劃；算計。
  1. Surveying of geological sections of tailings dams and its effect on seepage field calculation

    尾礦壩地質剖面概化及其對滲流場計算的影響
  2. This thesis primarily makes below the work of a few aspects : ( 1 ) the method to append the section line in the geological section plane and the geological plane graph intersected each other ; ( 2 ) the principle and method that automatic determinate of orebody on transverse section with the neural network theory was presented, and draw the slippery boundary of ore ; ( 3 ) the method that drawing the surveying well and lane way engineering in the geological and survey graph ; ( 4 ) the method to automatic calculation and statistics output ore reserves and grade ; ( 5 ) the method that automatic creating the geology cross section of the hole ; this thesis realizes automation for managing geological graph based on the substantive research work

    本論文主要作了以下幾個方面的工作： （ 1 ）提出了在相交平面圖和剖面圖中添加剖面剖切線的方法； （ 2 ）提出了應用人工神經網路理論確定剖面中礦體界線的理論和方法以及礦巖界線圓滑的原理與方法； （ 3 ）實現了礦山生產實測工程數據處理與地測圖件的有機結合； （ 4 ）實現了礦塊地質品位和儲量的自動計算和統計輸出； （ 5 ）提出了中深孔炮孔排面地質剖面圖自動剖切的原理和方法。本論文在大量研究工作基礎上，實現了地測圖件管理的計算機自動化。
  3. The influence factors and optimal scheme of connected - triangle surveying with shaft is analyzed in detail. the formula for calculating the lateral transfixion errors of underground traverse with added gyro orientation line is derived strictly, the calculation results show that the accuracy can be increased obviously by the way of orienting added gyro lines

    詳細分析了聯系測量各因素對方位傳遞的影響，探討並比較了加測陀螺方位角后地下導線的精度提高問題，論證了加測陀螺方位角后直伸等邊導線終點精度的嚴密計算公式及陀螺方位邊布測的最佳位置。
  4. Research progress on surveying and calculation of evapotranspiration of plants and its prospects

    植物蒸散耗水量測定方法研究進展
  5. This paper briefly introduces the basical principles of finite element method which can be used for analysis of vehicles structure, describes the principles and methods of design optimization for vehicles structure parameters, establishes the finite element models of semi - dragging trucks, which is used to load cement dispersedly and container semi - dragging trucks, applying the ansys software, calculates the static strength, then proves the calculation results to be accurate by means of non - electric charge surveying experiment. at the same time, the author puts forward the model and methods of optimization design for structure parameters of vehicle frames, exploits the applied software of semi - dragging trucks, does optimization design. analyzes the feasibility of the optimization results, then gives the structure improve direction. besides this, the author has had initiative research about interface software, etc

    本文簡要介紹了可用於汽車結構分析的有限元法的基本理論，闡述了汽車結構參數優化設計的原理和方法，建立了散裝水泥罐式半掛車和集裝箱式半掛車車架的有限元計算模型，利用有限元軟體? ansys進行了強度分析，並對罐式半掛車通過電測試驗驗證了計算模型和計算結果的正確性；論文還提出了半掛車車架結構參數優化設計的模型和方法，開發出了半掛汽車的結構優化設計軟體，調用了ansys軟體對其進行了優化設計，分析了優化結果的可行性，並給出了該半掛車的結構改進的方向。
  6. This is the first time that the author wrote down the technology to be a thesis for his post - graduate degree. the author hopes geotechnical professors and experts to research and develop this support system far because initial surveying dates are too limited and the theory is too simple. that the calculation method must be superficial

    此次是筆者首次對該技術進行系統整理以作為本人的碩士論文，山于原位測一試數據不足又無成熟理論參考，因此計一算方法定顯淺薄，望教授及同行專家指導完善，更希望能與同行們繼續對該技術進行進一步研究。
  7. Real - time calculation method of 3d surveying data for large highway bridge curve and its application

    大型公路橋梁曲線段三維測設數據實時解算方法及應用
分享友人
分享到 Line

分享到臉書