switch module 中文意思是什麼
switch module
解釋
開關組件-
This paper presents a method that chopping wave is done by switch devices which consist of three - level resistance regulating module and intelligence power module ipm, and which realizes constant - current discharge of storage battery. to achieve the intelligence control of the drive protection and the discharge process of ipm, the paper designs circuit formed by igbt threshold drive pulse pwm signals. ipm fault - blocking protection circuit and microcomputer 80c196. the devices can accurately control the 0 ~ 150a discharge current and the discharge time of the storage battery and calculate the releasing power
實現蓄電池恆流放電過程智能控制是蓄電池放電裝置發展的必然趨，本文提出了一種通過三極電阻調節模塊和由智能功率模塊ipm為開關器件進行斬波從而實現蓄電池恆流放電的方法。為達到對ipm的驅動保護和放電過程的智能控制，文中設計了igbt門極驅動脈沖pwm信號形成電路和ipm故障封鎖保護電路及由單片機80c196為核心的微機控制器。本裝置能夠對蓄電池進行0 150a放電電流及放電時間的精確控制及釋放容量的計算。 -
Various technoiogies are invoived in the design of optical reiay networking, mainly inciuding the design of access circuit of optical relay and the design of opticai relay module software in switch
光中繼組網的設計涉及到多方面的技術，主要是光中繼接入電路的設計和交換機光中繼模塊軟體的設計。 -
3 ) the content of generator module design includes the design factor, design outline, software design and experimentation. the generator module must complete the analog signals calculating, and make an order for shutting off connected generators in the condition of generators settings, concatenated logics and switch signal input, then communicate with the decision module
3 ）發電機模塊的設計內容包括設計考慮因素、設計要點、軟體設計以及實驗驗證等，模塊必須完成對接入的發電機機組模擬量的計算；在機組設置、連鎖邏輯和開入信息等條件下對接入的發電機機組排出一個切機順序；完成模塊間通信。 -
Ecg monitor module included signal collection channel and related data processing based on mcu. the signal collection channel which adopted high performance integration instrument amplifier was designed according to the features of ecg signal. msp430f149 mcu was used in controlling lead - switch, state - switch and the a / d conversion
根據心電信號特徵，使用儀表放大器設計了高指標的心電信號採集通道，由msp430f149單片機進行控制，可選擇多導聯切換檢測，以及切換工作模式，並對模擬信號進行a / d轉換。 -
Based on the degree of urgency of going into graceful ospf restart, the reason of graceful ospf restart is divided into software - restart and hardware - restart, and the way of graceful ospf restart is divided into pre - restart mode and post - restart mode accordingly. after the compare with the traditional ospf realization method and the analysis on the mechanism of the trigger of graceful ospf restart and synchronization of link state database and the exchanging with the route management module ( rtm ), it is figured out that how to choose the restart mode and how to switch from pre - restart mode to post - restart mode, and how to synchronize the link state database, and how to define the interface and process flow exchanging with protocol supporting module, and how to deal with the forwarding table on the condition of multiple route protocols who also have the capability of graceful restart. finally, the idea of graceful ospf restart with two modes above was realized in the t series routers that belong to a telecommunication corporation
本文首先找出了引起溫和重啟的各種原因，然後根據溫和重啟的緊迫程度，提出把溫和重啟的原因分為硬重啟與軟重啟，並設計相應的前啟動模式與后啟動模式;結合傳統ospf協議的實現方法，通過對其觸發機制、數據庫同步機制、與支撐模塊的交互機制以及多協議同時重啟時路由同步機制的分析，解決了在溫和重啟過程中啟動模式如何選擇與切換、數據庫如何同步、與協議支撐介面如何定義與交互的問題，並揭示出在多協議同時進行溫和重啟過程中所必須遵循的一般規律，最終在一個通訊企業的t系列路由器上實現了兩種模式下基於ospf協議的溫和重啟。 -
With adjustment of gun switch and module, it could satisfy the client ' s different width coated adhesive demand
通過調節槍體開關或模塊，滿足用戶不同寬度的塗膠要求。 -
Before the 1990s, the digital transmission equipment was based on the technical standards of plesiochronous digital hierarchy ( pdh ). in order to connect the switch to pdh transmission equipment, the switch side needs lots of terminal equipment of the primary rate, i. e., 2048 kbits ( 2m ) switching terminal circuits in compliance with itu - t standards ( e. g. s1240 s dtm trunk module and axe10 s etc module ) and ansi - standard - based 1544 kbits ones
在90年代初期以前，數字傳輸設備是建立在pdh （ plesiochronousdigitalhierarchy ）技術標準上，為了連接交換機到pdh傳輸設備上，在交換機側需要大量的符合基群速率的終端設備，即符合itu - t標準的2048kbits （ 2m ）交換終端電路（如s1240的dtm中繼模塊， axe10的etc模塊）和符合ansi標準的1544kbits交換終端電路等。 -
And the selection and design of switch - in module, switch - out module, communication module, clock module, data storage module, keys module and frequency detecting module are also discussed
論文中還給出了開關量輸入、開關量輸出、通信模塊、時鐘電路、數據存儲器、按鍵電路和頻率跟蹤電路等各功能模塊的選擇方法和設計原理。 -
The fundamentals of switch power supply are firstly introduced in thesis where the control module of positive output voltage is discussed in detail, which is followed by the sub - blocks simulation, the feed - forward system analysis
本文對開關電源的基礎知識進行了介紹，重點討論了在該電源管理晶元中的正電壓輸出電路設計和各子模塊模擬，對輸入電壓前饋控制方法進行了分析。 -
The system selects micro control unit and programmable logic device as the core of controller, gsm terminal module as communication device, gps as position equipment, a / d sampling for voltage and current checking, solar battery as power supply, switch dc - dc as power voltage conversion, and so on
以微處理單元與可編程邏輯器件為核心搭建系統控制器，選擇gsm無線通信模塊實現系統通信，全球定位系統實現水標燈定位， a d采樣與轉換實現電壓電流檢測，太陽能電池為系統供電，開關型dc - dc實現電源電壓轉換。 -
Hardware configurations of the automatic test system for t / r modules is achieved by reasonably selecting programmable measurement instruments according to the measurement requirements and then integrating them with the t / r module to be tested by a programmable switch matrix
根據測量要求，合理選擇可程式控制測量儀器，利用可程式控制開關矩陣將各測量儀器與被測件（ t r組件）有機地結合起來，完成了t r組件自動測試系統的硬體配置。 -
Durning study of the subject, realizating comprehensive rf front - end simulator and starfabric data - distributed interface module in hardware. moreover, it elaborates the achievement of a system of data - distributed based on starfabric technology, by designing hardware modules, multi - entrance high - speed switch module, signal processing module and pc terminal
在課題研究期間，在硬體上完成了高速數據分發系統中的綜合射頻前端模擬器和starfbric數據分發介面板設計及實現，並用所設計的硬體模塊，加上多埠高速交換模塊、信號處理模塊和pc終端實現了一個基於starfabric技術的高速數據分發系統。 -
Essm engine speed switch module
引擎轉速開關模組 -
General specification for microwave integrated pin single - pole switch module
微波集成pin單刀開關模塊通用規范 -
Several progresses are made in the development of software and hardware in the video signal switch module
對視頻混合電路模塊的軟硬體開發調試也取得了一定的進展。 -
It focuses on the system architecture and hardware realization of the gigabit ethernet switch we designed, which include the control module with mpc8241 embedded processor core and the switch module
重點介紹了mpc8241嵌入式處理器為核心的管理模塊以及交換模塊的系統結構和硬體實現。 -
The third and fourth chapters are the main parts of the thesis, explain the design thinking about the control module and switch module respectively, emphasize the work principle of every chips and the realization of all function in details
第三章和第四章是本論文的主要部分，分別介紹了管理模塊和交換模塊硬體系統的結構設計思想，著重討論了各功能模塊晶元的工作原理及功能實現方法。 -
Therefore, the project is not only academically valuable but also practically useful. in the course of studying and designing the concentrator, we firstly analyzed its function, defined its function module and also selected ethernet switch to implement switch module
在對集中器的研究設計中，首先分析了集中器的功能組成，劃分其功能模塊，並對其中的交換機的選擇進行了方案比較分析，最終確定了對以太網交換機選擇。 -
Automatic vehicle system are made up of several moduls, those moduls are vector electronical map module, position module, communication module, multimedia player module and video signal switch module. in this system, we can realize the position and navigation of vehicle in graphics mode, and demand geographical information, make use of wireless communication, enjoy the multimedia player and so on
該系統由矢量電子地圖模塊、定位模塊、通信模塊、多媒體視頻播放模塊及視頻混合電路模塊這幾個模塊有機組成，用於實現車輛圖形化定位導航、信息查詢、無線通信、多媒體播放等多種功能。 -
After the discussion of the switch reference, the characteristic and regularity of the switch and merge by dual grating scales, this paper designs the hardware circuit to execute the method of dual grating scales ’ dual measuring, count values switch and merge, designs different circuit module of the dual grating scales ’ s signal process based on fpga, such as the quadruple module, the speed identify module, the switch module, the merge process module
經過對雙光柵計數切換基準、切換與合成特徵和規律的探討，本文設計了實現雙光柵尺雙重測量、計數值切換合成法的硬體電路，主要通過可編程晶元fpga ，設計了雙光柵尺信號處理的各電路模塊，如雙光柵尺信號四倍頻辨向模塊、速度判斷模塊、切換模塊、計數值合成處理模塊。
分享友人