tensile property 中文意思是什麼
tensile property
解釋
抗拉性能-
This paper analyzes the influence of sra on the shrinkage - cracking property of hpc by designing five check - up experiments including desiccation - shrinkage, autogeous shrinkage, flat - restraint, anti - chloride ion penetration and ultimate tensile strain
摘要設計了乾燥收縮、自收縮、平板約束、抗氯離子滲透性以及極限拉應變等5種試驗方法來檢驗減縮劑對高性能混凝土收縮開裂性能的影響。 -
When fillings is other materials ( unprocessed montmorillonite, powder coal ash, co - composite of powder coal ash and organo - montmorillonite, co - composite ofcarbonizing calcium and organo - montmorillonite ) in the binder and content of organo - montmorillonite in the binder is five percent decided by tensile - shear experiment, tensile - shear strength of binder is up to tiptop ; at the same time, this paper carries out abrasion experiment, and, by comparison, concludes abrasion property of coating is optimum when content of organo - montmorillonite in the binder coating is five percent, and observes abrasion sample under set
當膠粘劑中填料為其它物質（未處理蒙脫土、粉煤灰、粉煤灰和有機化蒙脫土共復合、碳化鈣和有機化蒙脫土共復合）時，通過拉伸剪切試驗確定膠粘劑中有機化蒙脫土含量為5時，膠粘劑的拉伸剪切強度最高；同時進行了沖蝕磨損試驗，通過比較得出，當膠粘劑塗層中有機化蒙脫土含量達到5時，塗層的耐沖蝕磨損性能最佳，並對沖蝕磨損試樣在掃描電子顯微鏡（ set ）上進行觀察。 -
The mechanical tests result showed that when the mmt content is 2 % and the compatilizer content is 15 %, the pmc has best mechanical property. the izod impact strength is 16. 45 kj / m2 and the tensile strength is 35. 77 mpa, increasing 280 % and 4. 3 %, compared with pure pp. the pom photo indicated that the o - mmt can reduce the scale of spherical crystal of pp
以am為插層劑得到的聚丙烯蒙脫土納米復合材料中，蒙脫土保持剝離狀態，但力學性能不理想，當土含量為0 . 5時，材料的沖擊強度為9 . 58kj m ~ 2 ，拉伸強度為25 . 5mpa 。 -
This subject is to combine the steel fiber reinforced concrete with the lightweight aggregate concrete to form a steel fiber reinforced lightweight aggregate ( haydite ) concrete, which owns the advantages of high toughness of steel fiber reinforced concrete and the light weight of lightweight aggregate concrete. in order to get the main character and mechanical property parameter of strength and deformation of steel fiber reinforced lightweight aggregate concrete, we do the experiments of cubic compressive strength, splitting - tensile strength, bending strength, elastic modulus and axial compressive strength and summarize the influence laws to the relation of mechanical performance of steel fiber reinforced lightweight aggregate and the quantity of steel fiber
鋼纖維輕骨料混凝土兼有鋼纖維混凝土的韌性高和輕骨料混凝土質量輕的優點，為了掌握這種新型材料的主要特徵和強度、變形等力學性能，本文進行了鋼纖維輕骨料混凝土的立方體抗壓強度、軸心抗壓強度、劈裂抗拉強度、抗折強度和彈性模量等試驗研究，總結出鋼纖維摻量對鋼纖維輕骨料混凝土的力學性能的影響規律。 -
In this paper, 130mm diameter hot - rolled bars ( 3 transus temperature is 798 c ) were used in experiments. the superplastic property of ti - 1023 alloy was studied systematically by the experiments of tensile and compression. the preparation method of fine - crystalline structure and the processing parameters of superplastic forging are optimized
本文以130mm熱軋棒材為原材料，通過超塑性拉伸和超塑性壓縮試驗，對ti - 1023合金的超塑性進行系統研究，研究坯料細晶組織制備方法，優化超塑成形工藝參數，為高筋薄腹板復雜形狀ti - 1023合金鍛件超塑性等溫模鍛工藝的制定提供試驗依據。 -
Test method for tensile - impact property of plastics
塑料拉伸沖擊性能試驗方法 -
With the prerequisite of meeting requirement of its working performance, the mix design of common grades can be concluded though strength test if we check various property of the said concrete with the certain mix design, such as compressive strength, tensile strength, elastic modulus, reinforcement wrapping strength, leakage resistance, shrink property and charring resistance, and compare them with property of ordinary concrete, we will find that the various dynamic property of self - densifying high performance concrete is very satisfactory and the durability is quite ideal
在滿足自密實高性能混凝土工作性能的前提下，通過強度試驗得出常用強度等級混凝土的配合比，檢測該配合比下的自密實高性能混凝土的抗壓強度、劈裂抗拉強度、彈性模量、鋼筋握裹力性能、抗滲性、收縮性、抗炭化性等性能，以及各種性能與普通混凝土的比較，驗證自密實高性能混凝土硬化后的各方面力學性能是完全能夠符合要求的，並且具有較高的耐久性。 -
Secondly, the effect of transverse deforming on the property of the wedge pressing was studied. the results showed that : the wedge pressing stock with the transverse deforming amount of 10 % acquired the best performance. the highest density got the biggest rate of slope while with the amount of 30 % the curve was more some special structure and performance as following : the large porosities was crushed into small or linear ones with the high - direction deformation amount of 20 % ; as the increasing of the high - direction deforming, the particles got a further deforming, the porosities got a further crushing, the small porosities were mergered by the large ones and the former then disappeared ; when the amound reached 60 %, the quantity of the porosities would obviously decrease which made the materials compact, the microstructure more uniform and the density and hardness curves more horizontal, the relative desity could reach 99. 7 %, the tensile strength b of the as - compacted samples reached 408mpa with the yield strength s teached 289mpa and the elongation percentage reached 13. 6 %. in addition, the microstructure of the wedge pressing stock under the pressing temperectureof 450 was uniform, the porosities and the boundries of the grains basically disappeared and the conjunction between particles was great
採用雙向楔形壓制，大尺寸噴射沉積5a06鋁合金楔壓坯的組織和性能變化具有如下特點:當高向變形量為20 %時，大的孔洞變形破碎為小的孔洞，或呈線狀孔;隨著高向變形量的增加，顆粒進一步變形，孔洞進一步破碎，大孔「吞併」小孔，小孔塌陷並逐步消失;當高向變形量達到60 %時，孔洞量大為減少，材料基本緻密，組織趨于均勻，楔壓坯料的密度、硬度變化曲線接近水平線，坯料的相對密度達99 . 7 % ，抗拉強度_ b = 408mpa ，屈服強度_ （ 0 . 2 ） = 289mpa ，延伸率= 13 . 6 % ;對比其它的壓制溫度，在450楔形壓制的坯料組織均勻，孔洞及顆粒邊界基本消失，顆粒之間冶金結合良好。 -
This paper mainly analyzed sn - cu eutectic solder alloys ' research production of wetting characteristics and their tensile property, shear property, creep property, fatigue property and thermal fatigue property when the block of sn - cu eutectic solder alloys joined by backing
摘要主要敘述了錫銅合金的潤濕性質以及它們的塊材與基材連接時的拉伸特性、剪切特性、蠕變特性、疲勞特性及熱疲勞特性等方面的研究結果。 -
Alloying element to high tensile steel weld metal mechanical property influence
合金元素對高強鋼焊縫金屬機械性能的影響 -
The expansive property of concrete curing in water is better than that curing in air. the curing time of multiple anti - cracking and impermeability concrete can not less than 14 days. ill to take all account of the factors such as raw materials, construction, curing, and tensile strength, limit tensile strain, etc., which have effect on anti - cracking property of concrete, the overall crack probability is brought forward to access anti - cracking property of concrete, with aid of mathematics
為了全面地考慮原材料、施工、養護、抗拉強度和極限拉伸率等因素對混凝土抗裂性能的影響，利用數學概率分析方法，引入體積開裂概率的概念評估混凝土的抗裂性能。應用材料復合技術，無機-有機多組份復合，研製出一種新型復合抗裂材料，提高混凝土的抗裂防滲性能，且滿足混凝土的強度和工作性要求。 -
Moreover, rare earth ceo2 can clean the melt and the face of reinforced particles and improve the wettability between the reinforced phase and melt and the property of material. proper additive mg and rare earth can improve the hardness, wear - resisting property tensile - strength, elongation percentage of tic / al, tic / al - si composite
加入適量添加劑mg和稀土ceo _ 2使原位tic al ， tic al - si復合材料的硬武漢科技人學碩1 ：論義度、咐磨性、抗拉強度、延伸率得到很大的提高。 -
Early age cracking of concrete has re - emerged as an important issue all over the world in recent years. the stress, due to restrained volume change related to thermal deformation and shrinkage in the early age concrete, is the main driving force for the deleterious cracking in the construction stage. during the development of the stress, creep, a very important property of concrete, is always developing. creep contributes to 40 ? - 50 ? reduction of the elastically induced stress in the restrained specimen. ring test, a qualitative test, can provide information to assess the potential for cracking of different concrete. an overview of ring test developed in recent years and mechanism of uniaxial tensile creep test is described in this paper at first. then, an innovative test equipment based on ring test is outlined
近年來混凝土早期裂縫問題再次引起全球工程界的廣泛關注.早期混凝土由於體積變形受到約束而產生的應力是導致混凝土開裂的主要因素.在混凝土應力發展的同時，混凝土徐變也在同時發生著變化.有研究表明，徐變能減少40 ? - 50 ?的早期應力.圓環試驗是用於定性評價混凝土材料抗裂性能的試驗方法之一.本文首先分析了圓環試驗和單軸拉伸徐變試驗的原理，創造性地將圓環試驗用於測量早期混凝土的干縮徐變，並設計了試驗方案 -
It can be concluded that difference between tensile modulus and compressive modulus is an important property of soil and the solution of elasticity theory with different modulus in tension and compression is necessary and reasonable
可以認為，拉壓模量不同是土的重要性質，拉壓模量不同彈性理論解答的提出是合理的。 -
Secondly, considering the complexity of the analysis of inclined - loading pile, nonlinear finite element method is adopted to calculate the internal force and displacement of pile group under inclined loads, with the concept of equivalent width presented to simplify 3d problems into 2d problems. and a program is developed as well, which is able to consider the continuity, elastic - plasticity and layered characteristic of soil around the pile shaft. besides, the interactions among pile, base slab and soil are considered in this program and contact surface element is used to simulate slipping and crazing between pile and soil, or between base slab and soil under loads. then, the non - tension analysis is proposed, to reflect the low - tensile property of soil and concrete
在此基礎上，針對傾斜荷載下群樁基礎分析中的復雜性，提出採用非線性有限元對傾斜荷載下群樁的內力及位移進行分析，應用樁的等效寬度概念將空間問題簡化為平面問題考慮，並開發出能考慮樁周土介質連續性、彈塑性、分層性等因素的傾斜荷載下群樁內力及位移分析的計算機程序，並在程序中考慮了樁、土、承臺的相互作用，提出了採用接觸面單元來考慮荷載作用下樁與土體及承臺與土體間的滑移、開裂；並在此基礎上，提出了傾斜荷載下群樁基礎的「無拉力」分析方法，可有效地反映土體及混凝土材料的低抗拉特性。 -
The results show that the capacity and rate of alka - line absorption is respectively 10 percent more than that of american products, and twice as fast as that of them. the resista - nce is as good as that of them, and the electric property is better than that of them, but the tensile strength is not so good as that of them
研究制備的氧化鋯纖維布作為大容量鎳氫電池隔膜，組裝成電池進行實效考核表明，可以用於鎳氫電池隔膜;性能測試表明，吸堿率比美國產品高10 ，吸堿速率是美國產品的2倍，電性能優於美國產品。 -
This is the first time to apply prestressed carbon fiber to roadbed engineer in the world. the high tensile strength and corrosion - resisting property of prestressed carbon fiber make it possible that the soil is in triaxial state of stress. therefore, the embankment fill can be compacted, the settlement can be reduced and side slope stability can be improved
本課題第一次將預應力碳纖維技術應用於路基工程中，利用碳纖維的高抗拉強度和高耐腐蝕性，對其施加預應力，使路基土體處於三向受壓應力狀態中，從而加強路堤填料的密實程度、減少路堤的總沉降、增加邊坡的穩定性。 -
Making up nanopaint mixed with nano - silica, the improvement of its properties has been tested. the mechanic property of membrane formed increased, such as tensile strength, elongation at break, surface rigidity ; the scrubbing resistance and stain resistance of the paints has been improved. but it ' s the limitation that ideal results of properties of waterproofing and uv - screen have n ' t been gotten
實驗結果表明，塗膜的力學性能得到提高，如拉伸強度、斷裂延伸率和表面硬度；塗料的耐洗刷性能和耐沾污性能有改善，但防水性能和抗紫外性能無明顯改善，接觸角和吸水率數據無規律可循。 -
Their outstanding characteristics of low volume weight, high tensile strength and easy - to - cut property bring you great convenience in construction
出色的低容重、高抗壓強度、易切割等特點，給施工帶來更大的方便。 -
The study aimed at the cohering face of concrete after high temperature is little. only did the da lian university of science and engineering carried out the study of the bond property of the new - old concrete after 200 in 1999. in this paper, we use the basic mechanical index - splitting tensile strength to judge the mechanical property of the cohering face of the new - old concrete
本文的研究工作近年來國內外進行了大量高溫下混凝土材料受力性能的試驗研究和理論分析，但大都是針對混凝土本身，而對混凝土粘結面受高溫影響的研究甚少，只有大連理工大學在1999年作了200c后新老混凝土粘結性能的研究。
分享友人