test dial 中文意思是什麼

test dial 解釋
測試度盤
  • test : n 1 檢驗，檢查；考查；測驗；考試；考驗。2 檢驗用品；試金石；【化學】試藥；（判斷的）標準。3 【化...
  • dial : n 1 日晷 （＝ sun dial）。2 （鐘表等的）針盤；（儀表等的）標度盤；（電話的）撥號盤。3 礦用羅盤；...
  1. By using 5000kn pressure - bent testing machine, the specimens of boulder concrete and crushed stone concrete were tested through three - point - bending method and wedge - split tensile method, the scale division of the index dial of pressure - bent testing machine is larger, whereas the predicted test - load is lesser, so the velocity of exerted load is controlled through observing the reading of the multimeter which is connected with the collecting systerm in order to continuously exert test - load

    本文使用5000kn壓彎實驗機，對不同強度等級的卵石混凝土和碎石混凝土試件分別進行了三點彎曲試驗和楔入劈拉試驗。試驗過程中，由於實驗機噸位較大，而試驗荷載預計較小，為了能夠有效地控制加載大小和加載速度，採用通過觀察與荷載傳感器相連的萬用表讀數控制加載速度的方法，連續加載。
  2. The test set comprises a hand operated pneumatic folding pump, capable of supplying pressure or vacuum with analog dial gauges to indicate pressure / vacuum levels

    整套測試儀包括一隻手動折疊氣泵，壓力管或真空管，並帶有顯示器以顯示壓力/真空水平。
  3. Specification for dial test indicators lever type for linear measurement

    長度測量用杠桿式千分測試指示器規范
  4. Dial test indicators lever type

    刻度測試指示計
  5. Inductive voltage dividers ( ivd s ) will be calibrated by comparison with the laboratory s 8 - dial ivd, normally at specific frequencies of 400 hz, 1 khz and 10 khz with an input test voltage of 25 v. the calibration normally involve measurement of voltage ratio ( magnitude ) of the output voltage related to the input voltage of the ivd

    感應分壓器一般按400hz 、 1khz及10khz等指定頻率及25v的輸入測試電壓，透過與本所的八刻盤感應分壓器對比而進行校正。校正工作一般包括測量該感應分壓器輸入電壓與相對輸出電壓的電壓比（幅值） 。
  6. Lever type dial test indicator

    杠桿式轉盤檢驗指示器
  7. Standard test method for size and squareness of resilient floor tile by dial gage method

    測微儀法測定彈性地板磚尺寸和垂直度的標準試驗方法
  8. Methods of test for length change of mortar and concrete part 3 : method with dial gague

    灰漿和混凝土長度變化的試驗方法.第3部分:千分表檢測法
  9. Verification regulation of dial test indicator

    杠桿表檢定規程
  10. Dial test indicator

    刻度盤試驗指示器
  11. Standard test method for measurement of resilient floor plank by dial gage

    用千分表測量彈性地板的標準試驗方法
  12. After completion of this task, the reading from the dial by traditional mechanic - contacted test can be replaced by the reading directly from the monitor of computer gauge comparator, and the precision is very high, under all conditions are satisfied in the laboratory, its precision can be as high as 0. 01 u m

    本課題的完成解決了傳統的機械接觸式測量只能從度盤讀數，電腦量塊比較儀可直接從電腦顯示器讀出結果，而且精度相當高，在實驗室所有條件滿足的情況下，精度可達0 . 01 m 。
分享友人
分享到 Line

分享到臉書