the cutter 中文意思是什麼

the cutter 解釋
劊子手
  • the : 〈代表用法〉…那樣的東西，…那種東西。1 〈用單數普通名詞代表它的一類時（所謂代表的單數）〉 （a） 〈...
  • cutter : n 1 切者；裁衣人；【電影】剪輯員。2 切刀，切斷機；刻紋[錄音]頭，利齒，門牙，前牙。3 〈美國〉（單...
  1. The results indicate that a stable deformation localization band occurs in the coal cutting course and develops to macroscopic crack ; the deformation localization band is slantwise ; while the cutter tooth is used, the deformation localization develops slowly, and the localization becomes wider and the strain value in the band area higher afterwards ; when the point - attack pick used the localization develops quickly and the localization band becomes narrow and the strain value in the band lower

    研究表明：截齒截割煤體過程中，煤體出現穩定的變形局部化帶，且最終發展為宏觀裂紋；煤體變形局部化帶為一個傾斜帶：刀齒截割時，變形局部化發展較慢，但產生變形局部化后，局部化帶寬且帶內應變值較高；而鎬齒截割時，變形局部化發展較快，但產生局部化后，局部化帶窄且帶內應變值不如刀齒高。
  2. Analyse the tooth geometry of klingelnberg cyclo - palloid spiral bevel gear., according to the relative position and kinematic relation of the cutter heads, virtual crown gear and the processed wheel blank, established the system of coordinates of the gear cutting, dedcuced the tooth face equation of the virtual crown gear, according to relations of the gear cutting and space theory of engagement, deduced the tooth face equation of klingelnberg cyclo - palloid spiral bevel gear, and drawing the three - dimensional graphs of the virutal crown gear and klingelnberg cyclo - palloid spiral bevel gear according to the design and setting parameters

    對克林貝格擺線齒錐齒輪進行齒面幾何分析。根據銑齒加工中刀盤、搖臺和輪坯的相對位置和相對運動關系建立了切齒嚙合坐標系，由矢量的旋轉推導了產形輪齒面方程;根據空間嚙合原理和切齒嚙合關系推導了被加工齒輪的齒面方程;由設計參數和銑齒調整參數計算得到齒面離散數據，繪制了產形輪和擺線齒錐齒輪的三維齒形。
  3. The shrill ringing of a bell broke up the card game on the cutter.

    刺耳的鈴聲打散了小汽艇的牌局。
  4. The cutter can be mounted like a pennib in a simple holder.

    刻刀可象繪圖筆一樣，固定在簡易的刀架上。
  5. It makes sampling data regularized by means of man - machine interactive mode and procedure method, respectively. the driven data of the cutter guide is generated, which is based on sampling data processed. it proposes an intelligent data reduction algorithm which bases on the combination of straightness of curves, equidistance and distance deviation principle

    首先採集並分析了內輪廓數據，分別運用程序處理方式和人機交互方式實現采樣數據點的規則化處理;根據處理后的測點數據生成磨頭驅動數據;並提出了一種基於曲線曲率、等距及距離偏差帶的自適應數據壓縮方法。
  6. The approach includes ( 1 ) obtaining the cutter - location data based on parameter curves. ( 2 ) tessellation of the trim nurbs surfaces into triangles. ( 3 ) interference detection and tool - position correction

    在曲面的參數線上規劃刀位軌跡，將曲面用三角片離散逼近，利用刀具曲面與三角片的幾何相關性進行干涉檢查及刀位修正。
  7. When face milling is performed, the table can be moved longitudinally to feed the workpiece under or below the cutter.

    銑削端面時，為了將工件送到刀具底下或下方，工作臺可以縱向移動。
  8. Adjust the stubble adjusting plate alongside the cutter according to the requirement of harvesting plant to the perfect stubble height

    根據收割作物要求調整切割器兩側割茬調整拖板，達到理想割茬高度。
  9. The generation of the tool path means that by the geometrical models of parts, according to the adopted machines, the tools, the cutting patterns, the cutting allowance and etc., under some principles, the calculation of the cutter location was done and the tool path was generated

    刀具軌跡的生成是指通過零件幾何模型，根據所選用的加工機床、刀具、走刀方式以及加工余量等，按照一定的導動規則進行刀位計算並生成加工運動軌跡。
  10. The cutter adapters design of facing weld steel tubes

    平頭機刀盤的設計
  11. Based on the modal of different coolant and analysis of description about the impact in coolant, the parts, the cutter and lathe bed, it provides the technology basis for virtual machining

    此外，對冷卻液與零件、刀具、床身等的碰撞也進行了深入分析與描述，達到了噴濺效果，從而為虛擬製造提供了技術支撐。
  12. Stop when the work is finished, pull the clutch handle and the cutter will stop working. turn off the electric switch of engine and the engine will stop

    結束工作結束后，拉動離合手柄，切割器停止運轉，關閉汽油機電門，汽油機停止工作。
  13. With the cutter press we die - cut panels per various test standards and specifications

    按照測試標準裁切以便測試密度，碼重等
  14. In the paper, the cutter ladder of 500m3 / h dredger structure analyzed based on structural mechanics, finite element method and the risk analysis

    本文以500m ~ 3 h絞吸式挖泥船絞刀架為研究對象，從結構力學分析、有限元計算、風險評估三個方面加以研究。
  15. Dredger ( cutter suction dredger ) is a major kind of working ship, the cutter ladder is an important structure of the dredger, the design of cutter ladder has extreme sense

    挖泥船是工程船舶中的重要船型，絞刀架是挖泥船上的重要結構件，絞刀架設計方法的研究具有重要意義。
  16. The cutter suction dredger practicality model of the monitoring system is studied and designed in depth in this paper

    本文主要深入研究並設計了監控系統的絞吸式挖泥船實物模型。
  17. The cutter has high reliable cylinder and proportional electro - magnet for force, and the tools lift and down all controlled by computer so that the system has good stable

    切刀裝置採用高可靠性的汽缸和比例電磁鐵加壓，以保證系統穩定，抬落刀過程均由計算機控制，準確可靠
  18. Force stability analysis for the cutter of jsbz132 tunnel roadheader

    132型隧道掘進機截割頭受力穩定性分析
  19. The thesis researched the basic ways of the optimizations, the programming methods, the cutting ways and the cutter selections in the process of the nc machining

    機匣數控加工工藝優化研究。論文研究了機匣數控加工工藝優化的基本實現途徑，以及所採用編程方法、切削方式與刀具的選擇、切削冷卻液的選擇等。
  20. They include : 1. model of the mixture forming in the cutter

    其內容包括： 1 、泥管吸口處泥漿的形成過程。
分享友人
分享到 Line

分享到臉書