thread angle 中文意思是什麼

thread angle 解釋
螺面角
  • thread : n 1 線；細絲；〈英國〉麻紗，〈美國〉棉紗；纖維。2 細線，細流，細礦脈。3 （議論等的）思路，條理，...
  • angle : n 【英史】盎格魯人〈cf Angles〉。n 1 角，隅，角落；棱，嬗角。2 【數學】角，角位，角的度數。3 【機...
  1. This is a thread producing machine which uses its three thread rolling dies, mounted in the same seperation angle of 120 ', to realize roll forming of the workpiece, for metal has the performence of plastic deformation under the pressure operation

    該機床是利用金屬在壓力之下產生塑性變形的特點，用三個互成120度夾角的滾模，對工件進行滾壓成型的螺紋加工設備
  2. Firstly, from the angle of economy, based on synthesizing and deepening on western concerned theory, this research topic followed the thread of government and market, introduced the connotation of civil society, and then set up a basic theory frame of effective government from this aspect of optimizing economic behavior of government by means of friendly interaction of government, market and civil society

    本課題從經濟的角度，在根植于本土對西方理論進行綜合與深化的基礎上，循著政府與市場這根主線，再引入公民社會，以通過政府、市場與公民社會三者的友好互動來優化政府經濟行為為切入點，構建了一個有效政府的基本理論框架。
  3. The in - plane equivalent elastic modulus and tensile strength of stitched composite laminates are studied, and it ' s found that the in - plane equivalent elastic modulus decreases with the increase of stitch density, stitch thread diameter, maximal misalignment angle and the distortion width, and the range is about 5 %. the tensile strength of stitched composite laminate increases with the increase of stitch step and decreases with the stitch space. the

    研究結果表明：隨著縫紉密度、縫紉線直徑、最大纖維偏轉角和縫紉變形區寬度的增加，縫紉復合材料層合板面內等效模量逐漸降低，最大降幅一般在5 %左右；縫紉復合材料層合板的拉伸強度隨縫紉針距的增加而增大，隨縫紉行距的增加而降低，因此縫紉密度對拉伸強度的影響程度要看具體的縫紉針距和行距。
  4. Self - locking, floating, right angle anchor nuts with mj thread

    Mj螺紋直角游動板自鎖螺母
  5. Based on ansys, this paper studies stress concentration on single notch of eight kinds of high strength bolts used in grid structure, obtaining their stress concentration coefficients, discussing the effect of ascending angle, bottom radius of screw thread and bolt - ball on stress concentration, introducing their effect coefficients of a1, a2, a3, putting forward the formulae of stress concentration coefficient

    本文以ansys有限元軟體為研究手段，針對網架螺栓球節點的8種螺栓規格進行單缺口應力集中分析，定量求得相應的應力集中系數k _ t ；論述了螺紋升角、螺紋牙根圓角半徑r及球栓直徑比d / d對k _ t的影響，並引入相應的影響系數_ 1 、 _ 2及_ 3 ，最終提出了應力集中系數k的計算公式。
  6. There is a steel iron factory and two sets of production line. we have been able to produce all kinds of round steel, screw - thread steel, - steel, box iron, angle steel, h - rolled steel and those what you need to process

    我公司下屬軋鋼廠一個，有二套專業生產線，可以生產各種圓鋼螺紋鋼工字鋼槽鋼角鋼h型鋼，可以按用戶要求搞原材料加
  7. Cone - shaped bayonet ring couplings for rolling stock part 19 : cone thread angle couplings

    機車車輛用錐面卡套式管接頭.第19部分:管錐直角管接頭
  8. Curved - face bayonet ring couplings for rolling stock part 22 : cone thread angle couplings

    機車車輛用曲面卡套式管接頭.第22部分:管錐直角管接頭
  9. Cone - shaped bayonet ring couplings for rolling stock part 20 : cone thread angle coupling bodies

    機車車輛用錐面卡套式管接頭.第20部分:管錐直角管接頭體
  10. Curved - face bayonet ring couplings for rolling stock part 23 : cone thread angle coupling bodies

    機車車輛用曲面卡套式管接頭.第23部分:管錐直角管接頭體
  11. Pipe threads with 55 degree thread angle where pressure - tight joints are made on the threads part 2 : taper internal and external threads

    55密封管螺紋第2部分:圓錐內螺紋與圓錐外螺紋
  12. Pipe threads with 55 degree thread angle where pressure - tight joints are made on the threads part 1 : parallel internal and taper external threads

    55密封管螺紋第1部分:圓柱內螺紋與圓錐外螺紋
  13. Angle of thread

    螺紋牙形角
分享友人
分享到 Line

分享到臉書