three-control aircraft 中文意思是什麼
three-control aircraft
解釋
三操縱面飛機-
Police said three were killed and 29 hurt in thursday ' s crash when an elderly pilot lost control of his four - seater aircraft and flew it into the upper stories of the imposing high - rise that rowers above italy ' s financial capital
警方聲稱在星期四的這次撞擊事故中，有3名人員喪生， 29人受傷，起因是因為一位中年飛行員駕駛四座小飛機失控，撞上了義大利金融中心的這座雄偉大廈的高層。 -
1, the arrow next control around 2, y enable aircraft by clockwise or counterclockwise to 3. cache and the use of the space bar while firing bullets 4, only three lives
箭頭控制上下左右x y使飛行器按順時針或逆時針轉向-和空格鍵同時使用發射子彈只有三條命。 -
There are three control methods of aircraft landing gear : passive control, active control and semi - active control
對起落架的控制方法經歷了被動控制、主動控制和較新的半主動控制三個過程。 -
Flight simulator plays an important role in hardware - in - loop simulation, and a high - quality simulator is critical in developing a high - performance aircraft. this paper focuses on the performance improvement, it develops the controller of three axises and adjusts the control parameters in frequency - domain. it also concerns about some factors that influence the low - speed performance and draws some conclusions about the key points of performance improvement
本論文針對轉臺的品質整定，基於頻域法設計與實現了轉臺三軸的控制器，在頻率域內整定了轉臺的動靜態品質，並對整定過程中的問題和現象作了詳細的分析和研究，提出了轉臺品質整定的關鍵點和注意點。 -
In general, the control methods of the aircraft ' s landing gear shock absorbers are classified three categories : a passive type, an active type, and semi - active type
一般地說，飛機起落架緩沖系統的控制方式有三種：被動控制、主動控制和半主動控制。 -
From the management mode and integrating the aircraft part production characteristics, analysis and studies the integrated management of the manufacturing information, the organizing of the production plan and the control of the production process of the part manufacturing workshops which is under the cims environment, integrate with lean production idea. and this paper also applies concrete system analysis, promote general design plan and model establishing method. this thesis mainly discusses the workshop production practical flow, brings forward the new " month, week, day three class plan control " method, expects to apply effective control to the overall production process
本論文在了解了同行業企業的製造管理模式之後，以西安飛機工業（集團）有限責任公司零件製造車間為例，對零件製造車間進行系統的研究和分析，在此基礎上開發一個基於cims環境下適合零件製造車間的生產作業計劃管理系統，與精益生產方式（ leanproduction ） 、精益思想相結合，並對其管理系統進行研究，達成以生產計劃、生產調度為龍頭，充分利用工藝、工裝、工時定額等製造信息，科學編制生產的月、周、日計劃，高效的支配生產資源（如人、設備、工具、輔助材料等等） ，動態組織生產調度，準確預測隱患，全面監控生產過程，從而達到有效的提高生產效率的目的，並利用科學的管理方式最終提高我們的製造水平。
分享友人