throttle position 中文意思是什麼

throttle position 解釋
節氣門位置
  • throttle : n 1 〈方言〉喉嚨,氣管。2 【機械工程】風門,節氣閥,節流閥〈又叫 throttle valve〉;風門桿,節流桿...
  • position : n 1 位置;方位;地點。2 處境,情況;狀態,形勢,局面。3 姿態,姿勢。4 地位,身份;職位;職務。5 ...
  1. Now close the throttle to the idle position and connect the glow plug cord. the engine is now ready for starting

    節流閥到低速位置,接上火星塞電池,引擎已經準備啟動。
  2. The throttle plate moves toward the closed position as rated speed is reached.

    當達到發動機額定轉速時,節流板趨于關閉位置。
  3. The adjusting of screw prevents the throttle valve from moving to the fully closed position.

    調節螺釘防止節氣門運動到全關閉位置。
  4. In this experiment, adjusting the throttle to the specific position, and letting engine rotary speed change from the lowest to the highest, at the same time, the data of the water temperature, the fuel temperature, the air press and the rotary speed can be noted. moreover, we can measure the fuel quantity and the ignition angle

    實驗中,調節節氣門在特定位置,並讓發動機的速度依次從最低變化到最高,同時記錄水溫、油溫、進氣壓力和轉速等數據,還可以測出相應的噴油量、點火提前角。
  5. Tvps throttle valve position switch

    節流閥位置開關
  6. Move the throttle stick back to mid position - - swashplate moves to the mid point of its travel

    將油門操縱桿移動到中間,傾斜盤移動回行程的中點。
  7. As for the problems in the experimentation, such as the slow response speed of axes torque control, the disturbance of torque control to position control of throttle lever and the torque fluctuation of axis, solutions had been put forward and proved theoretically

    對于試驗過程中出現的以下問題,油門桿高速運動中輸入軸力矩控制的響應速度較慢,輸入軸力矩控制對油門桿位置控制的擾動,以及輸入軸力矩脈動現象,提出了解決方法,並且從理論上加以驗證。
  8. Ctps closed throttle position switch

    關閉節氣門位置開關
  9. This thesis analyzes all kinds of throttle components, points out the advantage of adapting eev, and analyzes the start - up and the discharge characteristics of eev, and dynamic response of refrigeration systems when the opening degree of eev is changed, etc. eev is placed into a tumoff position while the unit starts up, and after being kept for a period of time it is placed into a bigger position, after some more time it is put into a basic control

    本文對比分析了冷藏箱製冷系統各種節流元件的特點,指出電子膨脹閥應用的優勢,同時分析了電子膨脹閥的啟動特性、流量特性以及系統在閥開度變化時的動態響應。電子膨脹閥在啟動時應先使電子膨脹閥處于關閉位置,延時一段時間后,再將閥開至一個較大的位置,再延時一段時間后轉移到基本的控制。
  10. Tpout throttle position output

    節氣門位置輸出
  11. Pull and hold the trigger in the full throttle position then press & release the set up button one time

    拉遙控器上的油門到最大並保持住,然後按下再松開設置按鈕一次。
  12. Open the throttle to the idle position and turn the propeller over 10 times by hand to pressurize the tank

    打開節流閥到低速位置,用手撥動螺槳超過10次將油箱加壓。
  13. You can see at any moment in a lap speed, throttle / brake position, steering angle and track position

    你可以看到一圈中任何時刻的速度,油門/剎車的位置,方向盤的角度和賽道上的位置。
  14. Tps throttle position sensor

    節氣門位置傳感器
  15. Tp throttle position sensor

    節氣門開度傳感器
  16. Throttle position switch

    節氣門位置開關
  17. Tp throttle position

    節氣門位置
  18. The engine is tested on the dynometer using the software that can monitor the ecu ( electronic control unit ) internal dataflow. and the electronic control fuel injection system parameters ( e. g. position of throttle valve, engine speed, air temperature, engine temperature, duration of injection ) are acquired at many different working conditions of engine

    本文以hirth3203二沖程汽油發動機為研究對象,利用開發的ecu內部動態數據流監測軟體進行發動機臺架試驗,獲取了在不同的油門開度和轉速下電控燃油噴射系統的一系列工作參數,如節氣門開度、發動機轉速、進氣溫度、氣缸溫度、蓄電池電壓以及噴油脈寬。
  19. Tsp throttle solenoid position

    節流閥電磁線圈位置
分享友人