tightening torque 中文意思是什麼

tightening torque 解釋
緊固扭矩
  • tightening : 加密
  • torque : n. 1. （古代條頓人、高盧人戴的）金絲項圈。2. 【物理學】扭（力）矩，轉（力）矩。
  1. Clean and degrease the surfaces of the shaft to be fitted to. comply with the indicated tightening torque of screws ( mt )

    安裝前必須把軸徹底清潔和除油，收緊鑼栓（ mt ）時要參考上圖所示的數據
  2. Combines with a concrete subject, this paper, composed of seven chapers, makes a deep analysis on theory and experiment of key bolt fastening of engine. the first chapter presents the theory of tightening technology of the available bolt the second chapter gives a narrating about tighten technology availably in survey. pointing that the nature of torque control is axis preload

    本文結合一具體課題，第一章敘述了可控螺栓擰緊技術的理論，第二章綜述了可控擰緊技術，提出了扭矩控制研究的實質是控制螺栓的軸向預緊力。
  3. Metal construction. jointing by means of bolts with controlled tightening. calibration of torque wrenches

    金屬結構.可控拉緊螺栓連接.扭力扳手校準
  4. The method of torque - angle is adopted as the control method of the intelligent screw tightening machine on the basis of analyzing the excellence and deficiency of all kinds of control methods and taking practical situation into account. secondly, the design of the machinery of the tightening machine is explained in detail, almost all parts of the structure principle diagrams are given and an introduction of function of each part in the diagram is made concisely

    文章首先對螺紋擰緊的控制方法進行了探討，在分析各種方法優缺點和結合實際情況的基礎上採用扭矩轉角法為螺紋自動擰緊機的控制方法。然後，文章詳細地介紹了擰緊機的機構部分設計，給出了擰緊機的各部分的結構原理圖，並對原理圖中的各個環節的功能作了簡要介紹。
  5. Fasteners - tightening performance - torque angle simplified test method

    緊固件.緊固性能.扭矩角度簡易試驗方法
  6. The joint surface normal stress is worked out and then the minimum sleeve press - in force, by which tightening bolt number is determined, ensuring that the sleeve is fastened and the desired torque is delivered

    根據結合面的壓強計算了壓入襯套所需的最小壓入力，並依此確定緊固螺釘的數量，以確保壓牢襯套，滿足傳遞扭矩的需要。
  7. Fasteners - tightening performance - torque angle simplified test method ; german version en 14831 : 2005

    緊固件.上緊性能.扭矩角度簡化試驗法
  8. Test method for withstand tightening torque - ' f ' male

    耐扭緊力矩的試驗方法. ' f '凸模
  9. Testers work both clockwise and counterclockwise, so you can easily measure torque while tightening and loosening pieces

    扭力測試儀可順時針或逆時針測量扭力，因此可方便地測量扭緊和扭松時的扭力。
  10. Prevailing torque type hexagon nuts non - metallic insert with conical spring tightening washer. product grade a

    帶錐形盤簧密封墊圈的常用力矩形六角螺母非金屬鑲嵌件.級產品
分享友人
分享到 Line

分享到臉書