tooth parts 中文意思是什麼
tooth parts
解釋
否則刀俗語-
The thesis developed the optimization design software of geometric parameter for the worm gear including strength check module, the drawing contact lines module, the change lines of tooth thickness of worm, and the parametric modelling software for the reducer which includes parametric modelling of parts and assembly. the cad prototype system is very convenient because of its accessible interfere, simple operation and written in chinese. by input design parameters ， the cad system can make optimization design and strength check for the worm gear ， draw contact lines of tooth flank of worm - gear and change line of tooth thickness of worm ， judge if the tooth flanks of worm undercut and if the sideward tooth of worm - gear hob come to a point ， make project design and structure design for the reducer and draw its 2d parts and assembly
研究和開發了平面二次包絡環面蝸桿傳動的參數優化設計和校核軟體系統：包括幾何參數設計計算模塊，強度校核模塊，繪制齒面接觸線模塊，蝸桿齒厚變化曲線模塊和蝸桿根切判別模塊；開發了平面二次包絡環面蝸桿減速器外形與結構尺寸數據庫以及傳動效率數據庫，建立了平面二次包絡環面蝸桿傳動公差及極限偏差數據庫；開發了平面二次包絡環面蝸桿減速器參數化建模軟體：包括零部件的參數化建模模塊和裝配圖的參數化建模模塊，其中零部件的參數化建模包括蝸桿軸系的參數化建模、蝸輪軸系的參數化建模、箱體的參數化建模、端蓋的參數化建模、軸承的參數化建模和其它零部件的參數化建模軟體模塊。 -
In addition to a longer nose, aerodynamic modifications feature kfir - style small nose side - strakes to prevent yaw departure at high aoa, a pair of fixed delta canards on the upper parts of the air intakes, dog - tooth outboard leading - edge extensions, and short fences replacing leading - edge slots
除了一個加長的機鼻外，氣動布局的修改包括：在機鼻兩則裝上可以防止在高攻角下脫離偏航的「幼獅」式小邊條，一對固定在進氣道的三角鴨翼，鋸齒型外翼前緣，和代替前緣翼槽的短翼刀。 -
He who plucks out a tooth, parts with it freely, since the pain goes with it.
要拔掉一顆牙的人，慨然和它分手，因為拔掉之後就不痛了。 -
Various successive partial plastic forming methods for processing groove, including thread rolling, cross rolling and skew rolling, splitting, rolling of spline shaft, split rolling, open - die extrusion of spline shaft / gear, extrusion of internal screwed tooth socket parts with large helical pitch, integral cold forging for slot commutator, extrusion - ploughing for outside fin tube, drawing of tube with spiral internal / external ribs etc. have been introduced briefly
摘要介紹了用於加工槽的各種連續局部塑性成形方法，包括螺紋軋制、橫軋與斜軋、分劈、花鍵軸滾軋、劈分軋制、花鍵軸齒輪開模擠壓、花鍵套擠壓、槽型換向器整體冷鍛、外翅片管擠壓一犁削、內外螺紋管拉拔等。 -
The motion of the drive is also demonstrated. the paper mainly concludes the following works : the paper introduces the meshing theory of rolling cone - type toroidal drive and the motional relations of all parts, gives the formula of transmission radio. the relation between tooth numbers and helix angle of every parts is found out, and the assemble relation among all the parts is also given
本論文主要包括以下內容：介紹了超環面行星蝸桿傳動的傳動原理及各構件間的運動關系，分蝸桿固定和定子固定兩種情況，給出了這種新型傳動的傳動比計算公式，得出了各輪齒數與計算圓處螺旋升角間的關系和各構件間的裝配關系，從而為該傳動的優化打下理論基礎。 -
The tension damage resulted from powerful installation, improper dealings prior or during installation, is also one of reasons causing invalidation. 2. change of tooth the inadequate tension or the mismatched driving parts will lead to the change of teeth
一般說來，如果一條傳動帶的三英寸75mm一段內有三成更多個裂縫出現，那麼傳動帶的百分之八十的壽命已經完了，應該加以更換。 -
In the process of use and repair, before the confirmation of reliable connection of valve stem and handle, tooth disk or drive head and other parts, the valve can not access to medium to bear pressure, otherwise the valve stem may dash out, causes dangerous accidents
使用或維修過程中，在閥桿與手柄、齒盤或傳動頭等部件確認可靠連接前，閥門不能通入介質承壓，否則可能使閥桿沖出，造成危險事故。
分享友人