torsion bearing 中文意思是什麼
torsion bearing
解釋
摳轉軸承-
It shows that the result of resistance under bending and torsion by this method is almost same as that of experiments. correlate equations of bearing capacity of this structure under complex loads are deduced. four expressions of bearing capacity of this structure under complex loads, which are press, bending and torsion, are deduced in the end
最後利用軸壓、彎曲和扭轉作用的兩兩組合作用下的極限承載力相關方程，通過適當的簡化處理，就得到偏於安全的離心鋼管混凝土構件在軸壓、彎曲和扭轉三種荷載共同作用下的承載力計算公式。 -
Finally, a correlative equation about bearing capacity of this structural member under bending and torsion is deduced, which may provide design of such structural members a valuable reference. to imitate centrifugal concrete - filled steel tubes used in real structures, three - dimension models are built up by using finite element method. the resistance performance of this structure under complex loads is studied
利用三維有限元模擬分析方法對離心鋼管混凝土在彎扭組合作用、彎壓組合作用、壓扭組合作用下的構件彈性應力分佈進行了研究，分析了離心鋼管混凝土構件在組合作用下的工作機理和承載力的相關關系。 -
Besides, on the basis of the test data under bending and torsion and the theoretical analysis on the tubular, the relative relationship between the bearing values is derived. second, based on the elastic theory, this paper deduces the rules of stress distribution and main physical and geometric parameters by analyzing the elastic stress distributions when the tubular is under such conditions as torsion, bending, shearing, combined bending and torsion, and combined shearing and torsion ; additionally, taking the strength criteria of concrete and steel as reference, the paper proposes a set of theoretic equations for the relative relationship between the bearing values
本文利用彈性理論對扭轉、彎曲、剪切、彎扭聯合作用、剪扭聯合系列作用下的構件彈性應力分佈進行了研究，得出應力分佈與主要物理和幾何參數的規律；同時引入混凝土及鋼的強度準則，得出了彎扭、剪扭復合應力作用下的承載力相關關系的理論方程，可供工程設計使用。 -
Research has been done on the calculating methods of lateral stiffness and bearing capacity of the frame. according to experimental studies, finite element analysis and theoretical analysis, it develops to calculate lateral stiffness of frame with special - shaped columns of greater height - width ratio by using frame with rigid zones, and considering shear deformation of beam and columns. without considering the torsion of the whole structure, assuming the special - shaped column in the rc frame is flexural failure under uniaxial eccentricity force, putting forward the calculation method of flexural strength of special - shaped columns and the shear strength in a story for r. c
對異形柱框架分別按普通框架和壁式框架進行分析，並與空間有限元分析結果和試驗結果進行比較，提出了異形柱框架結構側向剛度的計算方法；在整體結構不產生扭轉且異形柱為彎曲破壞的假定下，提出了異形柱的受彎承載力及受剪承載力計算公式；提出了根據異形柱框架結構的破壞機構確定其樓層受剪承載力的方法。 -
Taking advantage of both, this paper choose t cross - section and enlarge detail dimension. the goal of optimum design is to increase torsion inertia moment and reduce shearing stress when moment of flexion and shear bearing capacity of single - beam is satisfied
綜合二者之優缺點，本課題選取t梁截面形式，用增大其細部尺寸的方法，以提高抗扭承載力為目標，滿足彎剪等承載力要求為約束條件進行主梁截面的優化。 -
Also the failure modes and the cracking torque, original stiffness, ultimate torsion strength and ductility are discussed in this case. the factors affected torsion bearing capacity of high - strength concrete frame column is analyzed too. the seismic performances of normal - strength and high - strength concrete frame column subjected to biaxial eccentric compression, shear and reversed torque are studied
以軸壓比和相對偏心距為主要研究參數，揭示高強鋼筋混凝土構件在單向、雙向偏壓剪單調、反復扭矩作用下的破壞特徵、開裂扭矩、剛度、強度、延性等特性，分析了影響高強混凝土框架柱抗扭承載力的因素。 -
By model experimentation of 14 high - strength concrete frame columns subjected to axial eccentric compression, shear and humdrum torque, of 9 high - strength concrete and 3 high - performance concrete frame columns subjected to biaxial eccentric compression, shear and reversed torque, the behavior of high - strength concrete frame column in warped section are studied the first time, and the mechanism of torsion bearing capacity of high - strength concrete frame column are discussed
通過14根承受單向壓、彎、剪，單調扭矩復合作用的高強鋼筋混凝土構件和9根高強混凝土、 3根高性能混凝土框架柱在雙向壓彎剪反復扭矩復合作用的模型試驗研究，首次研究了高強混凝土框架柱在翹曲截面上的受力行為，探討了高強混凝土框架柱抗扭性能的受力機理。 -
And the theoretical a nalyses done in this paper are listed below : first, the experimental data on the members of varied parameters under torsion demonstrate the general rule of the deformation while the tubular is under torsion. the paper establishes three phases of the deformation of the tubular under torsion, namely, the elastic deformation, the elastic - plastic deformation, and ultimate failure. through regression analysis, a simplified method is proposed for calculating the capabilities of the tubular under elastoplastic torsion, and the formulary for bearing value, is also recommended as a reference in engineering design
本文根據不同參數的構件受扭性能試驗結果，研究了該結構受力變形全過程的基本規律，提出了受鈕全過程的三個工作價段，即彈性變形階段，彈塑性變形階段和極限破壞階段，經分析回歸得到扭轉全過程彈塑性的簡化分析方法及承載力計算公式，可供工程設計參考；同時根據本文的彎扭試驗結果以及對離心鋼管混凝土構件進行的理論分析，推導了彎扭試驗相關承載力的關系。 -
By tests of 9 specimens subjected to biaxial eccentric compression, shear and reversed torque, the failure modes and the varying laws of cracking torque, original stiffness, ultimate torsion strength and ductility are discussed, with the change of axial stress level and relative eccentricity. then, the cracking bearing capacity, the ultimate capacity and the deformability of the specimens are obtained
通過9根承受雙向偏壓、彎、剪構件在反復扭矩作用下的試驗研究，以軸壓比和相對偏心距為主要研究參數，揭示鋼筋混凝土構件中雙向偏壓剪反復扭矩作用下的破壞特徵、開裂扭矩、剛度、強度、延性等特性和耗能性能，從而確定其開裂承載能力和極限承載能力及變形性能。
分享友人