trim control 中文意思是什麼
trim control
解釋
配平操縱-
Now chip - resistance of type 0402 has been manufactured overseas. but homemade laser - resistance - trimmer cannot trim it, one reason of which is the gap between their move - control - system. that ' s the aim of this article
目前國外已經開始生產0402型片阻，而國產激光調阻機尚不能滿足其調阻要求，原因之一就是其運動控制系統還有差距。 -
In the stability analysis were used typical longitudinal and lateral - direction stability index, while in the control analysis were estimated the control power requirements for trim, stabilization and maneuverability
穩定性分析包括靜穩定性和失速偏離判據以及模態特性分析；操縱性分析包括考慮平衡、增穩和機動性余量三方面的要求。 -
Through designs and developments the laser trim table system automatic control program, the system realized automatic provide resistors, check resistors, set resistors, change resistors and collect resistors functions, and realized automatic work progress
設計編寫了全部光刻平臺系統自動控製程序和人機交互程序，使其具有全自動上片、檢片、裝片、換片、光刻、收片功能，實現了激光調阻機的全自動光刻過程。 -
Secondly, it states the control principle of the new linear motor which drives the laser trim table. through adjusting proportion gain and integrated gain repeatedly, and the combination with the dynamic curve of laser trim table, it improves laser trim table ' s response
研究了帶動光刻平臺的新型直線電機控制原理，通過反復調整比例、積分等一系列伺服控制參數，並結合光刻平臺階躍動態曲線，提高了光刻平臺的響應性。 -
The thesis has two main parts. the first is the hardware design, which mainly uses the method of cpld and vhdl, design a circuitry with the trim, inspection, control, asynchronous serial communication, at last with rs - 485 difference transmittal mode outputs the inspection results to the pc ' s rs - 232
第一部分為硬體電路設計，採用了cpld器件和vhdl進行設計，通過vhdl描述，設計了整形、檢測、控制、異步串列通信為一體的電路，最後，檢測結果通過rs - 485差分傳送方式輸出到計算機的rs - 232串列口上。 -
This model is formulated as a non - linear state - space representation of helicopter flight dynamics, incorporating with blade element unsteady aerodynamics, a finite state dynamic inflow wake model, and flapping / lead - lag blade dynamic model. the formulation of the coupled rotor and fuselage equations enables the use of common solution techniques for trim and linearization in arbitrary steady flight condition as well as control response calculations
本項研究針對新機研製過程必須解決的品質評定、飛控系統設計等問題，按照ads - 33軍用品質規范的要求，建立了一個較完整的直升機非線性的、具有狀態空間表達形式的飛行動力學模型，進行了模型驗證工作，並以某樣例直升機為例，計算了ads - 33品質規范（ 3 -
This paper discusses the laser trim table control development and design of laser resistor trimming system from the following aspects. firstly, it analyzes the influence on laser trim quality by the dynamic feature, state feature and position accuracy of laser trimming table, and put forwards the control requirement of 0402 resistor
本文從以下幾方面對激光調阻機的光刻平臺系統進行了控制研究與設計：結合實驗分析了光刻平臺的動、靜態性能和定位精度對電阻光刻質量的影響，並針對目前最微小的0402型號電阻對光刻平臺提出了控制要求。
分享友人