twist distribution 中文意思是什麼
twist distribution
解釋
捻度分佈- twist : vt 1 擰，扭，絞。2 捻，搓；編，織，作，造。3 纏繞，卷。4 扭彎，扭歪；扭傷。5 曲解，牽強附會；搶奪...
- distribution : n 1 分配，分發，配給；分配裝置[系統]；配給品；配給量；【經濟學】配給方法，配給過程；分紅；【法律...
-
Then, we caculate the dynamic character of the reflective mtn cell with the optimized parameter, give out the distribution of velocity, twist angle and tilt angle at the midle of the mtn cell when switch on or off in consideration of the backflow
並針對選定參數的mtn液晶盒作了動力學上的計算。文中分別了給出mtn盒在加電壓和撤電壓時，引流效應對反射率的影響，並比較指向矢，速度，中間層的傾斜角等參量分佈的情況。 -
The surface panel method has been applied to predict the hydrodynamic performance of highly skewed propeller. the surface of propeller and its trailing vortex are discreted by a number of small hyperboloidal quadrilateral panels with constant source and doublet distribution. for highly skewed propeller, the conventional method generating grid oriented along constant radii will result in a high aspect ratio and a high skewness and a twist panel near the propeller tip on blade surface, which result easily in incorrect calculation results of velovity on blade surface, even in iteration divergence and calculation failure. a “ non - conventional grid ” is developed to acoid these problems. this grid can effectively solve the problem of the calculation and convergence for highly skewed propeller. the non - linear kutta condition of equal pressure on upper and lower at the trailing edge is executed by the iterative procedure. by sample calculating, the obtained results are satisfied the experimental data
採用面元法預報大側斜螺旋槳水動力性能，螺旋槳表面及尾渦面離散為四邊形雙曲面元，每個面元上布置等強度源匯和偶極子分佈.對于大側斜螺旋槳而言，槳葉表面採用常規的等半徑網格劃分方法在近葉梢處將導致大展弦比、大側斜和扭曲面元，這容易使槳葉表面速度的計算結果不正確，甚至會導致迭代過程發散及計算失敗.文中建立了一種「非常規網格」劃分方法，能有效地解決大側斜螺旋槳的計算和收斂問題.槳葉隨邊處通過迭代實現非線性等壓庫塔條件 -
Nevertheless, the widely existed overconstraints in the mechanisms will make the quality of the mechanisms very sensitive to the inevitable manufacturing, assembly errors ( especially, the errors resulted from the shape and position between kinematic pair elements and their axes ). at the same time, because the internal and external uncertain factors such as non - plane characteristic of dynamic parameters of links ( such as mass distribution, inertia forces, etc. ), bending and twist of links, and the changes of environment and operating condition are inevitable, they will form the disturbance to planar constraints and make them possess the characteristic of " uncertain "
但是，平面連桿機構中廣泛存在的過約束，造成機構對製造、安裝誤差特別是運動副元素的形位誤差十分敏感；同時，由於不可避免的內部和外部不確定因素的影響，常常會造成機構運動的「障礙」及系統中某些構件的變形和運動副中的附加動載荷，引起機械的振動、沖擊、噪聲等而導致機械的效率和工作性能的降低。
分享友人