vacuum-treated 中文意思是什麼
vacuum-treated
解釋
真空處理的- vacuum : n （pl vacuums vac ua ）1 真空；空處，空虛，空白。2 〈美口〉吸塵器（＝ vacuum cleaner）。vi vt 〈...
-
Shenyang alloy material co., ltd. ’ s transferring item is one of the important transforming items for us, which has approved by national financial department by means of using japan ' s loan, the importance of item includes the advanced half continual vacuum melting furnace 、 simultaneous x - ray spectrometer system 、 fluorescent analyzed instruments ; advanced annealed furnace 、 vacuum annealed furnace and other heat treated furnish etc ， and others totally 50 types
沈陽合金材料有限公司的搬遷改造項目是國家發改委和財政部批準的國家利用日元貸款改造重點項目之一，項目重點改造內容有引進國外最先進的半連續真空感應熔煉爐、 x熒光分析儀、直讀光譜儀；國內先進的罩式退火爐、真空退火爐等熱處理設備及一些冷加工設備，共增添新設備五十多臺套。 -
Specification for vacuum - treated steel forgings for generator rotors
用於發電機轉子的真空處理鋼鍛件規范 -
Vacuum - treated steel
真空處理鋼 -
Standard specification for vacuum - treated alloy steel forgings for turbine rotor disks and wheels
渦輪轉子盤和葉輪用真空處理合金鋼鍛件的標準規范 -
Specification for vacuum treated steel forgings, alloy, differentially heat treated, for turbine rotors
渦輪轉子用差溫熱處理真空處理鋼鍛件合金規范 -
Specification for vacuum - treated 12 t % chromium alloy steel forgings for turbine rotors and shafts
渦輪機轉子及軸用經真空處理的12 t %鉻合金鋼鍛件規范 -
Standard specification for vacuum - treated carbon and alloy steel forgings for turbine rotors and shafts
渦輪轉子和軸用經真空處理的碳素鋼和合金鋼鍛件的標準規范 -
Standard specification for quenched and tempered vacuum - treated carbon and alloy steel forgings for pressure vessels
壓力容器用經淬火和回火真空處理的碳素鋼與合金鋼鍛件的標準規范 -
Used in shaping process of brick production, the treated clay will be plastic extruded by up stage then via vacuum room into down stage, estruding into solid or hollow clay column of required cross section and shape which then cut into greenbrecks by green breck cutter
本機適用於磚瓦生產成型工段，可將經過處理的原料經過上級增塑擠出后落入真空室抽取空氣后再經過下級擠成規定斷面的實心或空心坯條，再經過切坯機製成一定規格的磚坯。 -
The shear strength increases by 3 - 6 times after improvement through vane shear test and the resistance increases largely through cpt. the soft foundation treated by vacuum combined with surcharge preloading is very effective. second, the mechanism and some problems of vacuum combined with surcharge preloading were analyzed
通過十字板剪切試驗與靜力觸探試驗，加固後土體的抗剪強度一般可提高3 6倍，錐尖阻力與側壁阻力也有大幅增長，說明真空聯合堆載預壓加固軟土地基的效果顯著。 -
Based on the former research, several works in this paper is listed as follow, which is studied by experiment research, theoretical analysis and numerical calculate : firstly, based on local observation and laboratory experiment result, consolidation mechanism of vacuum - surcharge preloading is analyzed form typical mechanics and microstructure seepage factor. a great deal of observed dada is employed to analyze the deformation characteristics of soil after being treated and variation law of pore water pressure
本文在前人工作的基礎上，通過試驗研究、理論分析、數值計算等手段主要進行了以下幾方面地工作： （ ）分析了大量現場觀測成果及室內外試驗資料，從經典力學和微觀滲流兩個角度解釋了塑料板排水真空-堆載聯合預壓法加固軟基機理，總結了該法加固的土體變形特點、孔隙水壓力變化規律。 -
Alloy steel heats are vacuum - treated on degassing units to reduce hydrogen contact to less than two parts per million and reduce metallic oxides
合金鋼熱是在脫氣裝置下進行真空處理，以將氫接觸減少到百萬分之二以下，並減少金屬氧化物。 -
The sample composition was analyzed by means of tg and x - ray diffraction. the following conclusions can be drawn from the experiments : given conditions, the sample powder that has the same xrd data as the standard fetioa can be gotten when use any method mentioned above ; the key in synthesis is to avoid the oxidation of fe2 +, so the whole process should performed under vacuum or neutral atmosphere, samples used by this study were prepared under nitrogen atmosphere ; the heat - treated time and temperature have some influence on the sample powder, results show that the proper time and temperature is 120 minutes and 1100 respectively
研究結果表明：在合適的反應條件下，用上述三種合成方法都能得到xrd數據與標準fetio _ 3物相基本吻合的粉體；合成反應需要克服的主要問題是防止體系中fe ~ （ 2 + ）的氧化，因此，整個反應必須在真空或者非氧化性氣體保護下進行，本研究需要的樣品是在高純從保護下合成的；煅燒的時間和溫度對最終的產物也有一定的影響，研究發現：合理的煅燒時間和溫度分別為120分鐘和1100 。
分享友人