velocity of gas flow 中文意思是什麼
velocity of gas flow
解釋
燃氣流速度-
The reaction activity was influenced by the velocity of gas, and the conversion rate was inverse ratio to the velocity of flow
同時研究了反應氣體流速對h _ 2s光催化氧化反應的影響， h _ 2s的去除率與流速成反比。 -
A reasonable position of driving nozzle helps to achieve the maximum material flow that also depends on other parameters such as backpressure, properties of conveyed material and driving gas. it is observed that, an increase of convergent section angle is harmful to the pneumatic conveying system, and also influences on the mass flow rate of conveyed material, the distribution of static pressures in injector and the pressure drops of conveying pipe. in addition, within a reasonable scope of air mass rate, increasing the driving jet velocity is more advantageous than enlarging the dimension of driving nozzle
試驗研究發現，氣體噴嘴位置對氣固噴射器的輸送能力影響最大，氣體噴嘴存在某一最佳位置，而這一最佳位置與背壓、輸送物料特性和輸送風特性相關聯；氣固噴射器的收縮角對其輸送能力、內部靜壓分佈和輸送管阻力特性均有適量影響，收縮角增大對整個輸送系統均不利；在適當的輸送風范圍內，提高氣體噴嘴出口速度比擴大氣體噴嘴尺寸更為有利，但氣體噴嘴出口速度過高會增加氣固噴射器和輸送管內的能量損耗，給輸送帶來不利的影響；系統背壓與氣固噴射器的氣體噴嘴出口速度的選取有關。 -
In this paper, high heat penetration into a moving particulate bed is described mathematically with a comprehensive heat and mass transfer model. the distribution of gas velocity and pressure, the temperature field of gas and solid in the moving particulate bed are examined for different conditions. the results show that thermal penetration into the moving packed - bed particles by fluid flow in porous media is high only in the position near the gas entrance. the thermal penetration thickness tends to increase with the fluid flow velocity and decrease with the particle moving velocity. in the region of thermal penetration, the porosity of solid bed has significant effect on gas field and pressure loss. it is feasible to reduce the gas pressure loss by a larger width / height packed bed in design and operation. the correspondence between thermal infection depth and particle bed height would be helpful to keep high oapacity of reactor and reduce the cost of operation
針對移動顆粒床中物料層內的高溫氣體滲流傳熱現象，考慮滲流與傳熱的相互作用，採用局部非熱平衡假設建立了多孔介質滲流傳熱物理數學模型並進行了數值計算.研究了不同情況下床內填充多孔介質中的流速、氣固溫度和床層壓力損失.計算結果表明，高溫熱氣對移動床顆粒料層的熱滲透主要發生在滲流入口端區域，增大入口滲流速度以及減小床層物料下移速度將導致物料溫度沿床高慢速下降，熱滲透深度擴大，熱滲透作用區域內的物料溫度水平提高.在熱滲透作用區域，孔隙率對流場和壓力損失有很大的影響.研究結果對于移動顆粒床反應器的設計與運行具有一定的參考作用 -
And the relationship between the size of a cavity and the velocity of cross - flow gas was investigated
當錯流氣速或壓力梯度足夠大時移動床內將發生空腔，空腔大小隨錯流氣速的增大而增大。 -
The saffman force does not affect the axial velocity of the flow, while it change the concentration of the particle. the gas - particle two - phase flows in the present of temperature were also numerical simulation
討論了絕熱、有溫差和添加熱泳力三種情況下的兩相流場，分析了溫度梯度、湍動能、軸向速度和顆粒濃度的變化。 -
Ph linearization method is employed to solve a nonlinear reynolds equation for a steady state and micro - scale flow field, and the approximate function expressions of gas dynamic pressure and velocity in the spiral groove are obtained
摘要應用ph線性化方法、迭代法，近似求解了螺旋槽內穩態微尺度流動場的非線性雷諾方程，求得了氣體動壓和速度分佈的解析解。 -
At last, three - dimensional mathematical model of gas - particle two phase turbulence was established, and it was adopted to study the gas - particle two phase rectangular jet as well. the distribution of the time - averaged velocity and turbulence intensity was studied, and some of the simulation results were compared with the experimental results ; the coherent structure of flow field was described in the three direction, the evolution and motion of the eddies was discussed too ; the dispersion of fine particles in the three dimensional space was also investigated
全面地分析了矩形射流氣相時均流場的速度、湍流強度的空間分佈規律，並就部分數值模擬結果與實驗結果進行了對比研究;描述分析了氣相流場湍流擬序結構，對流向、橫向和展向三個方向旋渦的空間結構特點進行分析研究，並分析了流向渦隨時間變化的發展、運動規律。 -
Pda laser flow velocity testing technique was used to measure the flow velocity of solid particles in the solid - liquid - gas three - phase system in a flotation cell and obtained the velocity distribution of solid particles so as to provide reliable data for the study on adsorption and deadsoption mechanism of particles onto and off from bubbles
採用pda激光流速測試技術，在固-液-氣三相體系中對浮選槽中固體顆粒進行了流速測定，獲得了固體顆粒的速度分佈，為礦粒與氣泡粘附過程和脫附過程機理的研究提供可靠數據。 -
Computer fluid dynamics ( cfd ) is adopted to simulate the flow fields of catalytic converter while researching the working process of emission postprocessor. the velocity field and pressure field of exhaust gas are obtained. methods of structural optimization of catalytic converter for improving gas flow and conversion efficiency are proposed
本文在汽車排氣后處理裝置工作過程研究方面，運用計算流體動力學軟體，對催化轉化裝置氣流場開展了模擬，得出了氣體速度場和壓力場的分佈情況，提出了以改善氣體流動和催化轉化效率的催化轉化裝置結構優化的方案。 -
And then simulations of gas - particle two phase plane wake and gas - particle two phase plane jet were carried out by using this model. after numerical simulations of the two flow fields were finished, series of analytical work was done. first, the distribution of time - averaged velocity, turbulence intensity was analyzed, and some of the simulation results were compared with those of the experiments ; the coherent structure of vortices in the near wall region of the plane wake flow were studied by describing the evolution of the eddy structures, including the forming, developing and shedding from the wall of the vortices in the near wall region ; the coherent structure of vortices in the whole field was also studied, such as the forming, developing, moving, pairing and merging of the eddies etc.
在對上述兩種流動形態的二維大渦模擬研究中，首先全面地分析了氣相時均流場的速度、湍流強度的分佈規律以及氣相速度的脈動規律等並就部分數值模擬結果與實驗結果進行了對比研究；分析了平面尾跡流場中近壁處旋渦擬序結構，全面和逼真地反映了近壁處旋渦的生成、發展和脫落的規律；描述分析了平面尾跡流和平面射流的全場流動旋渦擬序結構，從整個流場的角度反映旋渦的生成、發展、運動以及旋渦之間相互配對、合併的作用規律等。 -
The average slip ratio of droplet velocity to gas velocity across the gas core is about 0. 7 for oil - gas two - phase flow
油氣兩相流動時氣核中液滴與氣相的平均滑移比約為0 . 7 。 -
The size of the nanoparticles prepared with the flow - levitation method can be controlled by controling the gas pressure in the action tube, the velocity of cooling gas flow and the temperature in the melt metal globule
自懸浮定向流方法制備納米鋁粉和銅粉的過程中，通過控制反應管內的氣體壓力、冷卻氣體的流速、熔球的溫度等因素可以對粉體的尺寸分佈進行控制。 -
Taking some tubular air pre - heater used in one boiler whose capacity is 130 t / h as an example, new blue print with inner trachea is completed by means of computer program. several key design variables may be changed, such as diameter of pipe and velocity of flow of gas. these cases have been considered, and their results have also been compared with each other
比較了幾個重要的設計變量，如外管徑、煙氣流速等參數變化時，總傳熱系數和空預器本體管子總重量，阻力損失以及最低管壁溫度等幾個重要設計結果的變化趨勢，對內螺紋管空氣預熱器的設計具有借鑒意義；其間還分析了內螺紋管與光管在設計時的不同之處；最後，初步分析了內螺紋管的優化設計問題，提出了一些建議。 -
Based on the analysis of the existing dedusting method of advanced coal - fired combined cycle, a new dedusting concept was proposed for the high temperature and high pressure dusty gases according to the theory that the flow direction of the gas but the dust in dusty supersonic gas flow changes and the gas velocity decreases after the dusty supersonic gas flow passes through the oblique shock
摘要在分析先進燃煤聯合循環現有除塵方式的基礎上，根據含塵超音速氣流穿過斜激波后，氣體流動方向將發生變化，而灰塵顆粒方向基本維持不變的事實，提出了一種高溫高壓氣體除塵的新概念。 -
Development of low velocity gas flow sensor
一種低流速氣體流量傳感器的研製 -
The basic regulation of the ratio which changes along with the flo v rate of liquid and gas was obtained ; besides, the experiments discovered that the real velocity of the holes at flooding point is about llm ' s under different liquid flow rate, according to this the up limit of the compound tray can be reckoned
此外，實驗發現，不同噴淋密度下，復合塔板液泛時的篩孔真實氣速均為11m s左右，據此，可推算出復合塔板的操作上限。 -
So the measure technology of gas - solid two - phase flow yet belongs to the research field urgently waiting for developing based on the research achievements obtained by our task team recently, this dissertation further employed information process technology into parameter measurement of gas - solid two - phase flow, where the neural network technology was used to recognize the flow regime and the data fusion technology to measure the flow velocity of solid - phase particles, and the simulation research was worked
因此，氣固兩相流檢測技術尚屬一個急待發展的研究領域。本文在課題研究小組近年來取得的研究成果基礎上，進一步將信息處理技術引用到氣固兩相流參數檢測中。文中主要應用神經網路和數據融合這兩種方法分別進行氣固兩相流流型的辨識及固相顆粒流速的檢測，並進行了模擬研究。 -
And based on the simulation of dynamic arc characteristics during the interrupting process, the interactive mechanism of the arc and high velocity gas flow has been deeply analyzed, the variation of the gas flow parameters under the condition of arc clogging and interaction of arc and shock wave have been studied
在斷路器開斷過程動態電弧特性模擬的基礎上，深入解析了電弧與高速氣流的相互作用機理，研究了電弧堵塞情況下噴口氣流參數的變化，電弧與激波的沈陽工業大學博士學位論文摘要相互作用等。 -
Because gas and solid two phases flow in rotating and the inertia of solid phase is more than that of gas and the relative velocity between solid and gas phased is large, so it strengthens the process of heat exchanges, there fore the machine has strong drying capacity
由於氣固兩相作旋轉流動，固相慣性大於氣相，固相間的相對速度較大，強化兩相間的傳質傳熱，所以該機生產強度高。 -
But how the distributions of the velocity in the cabin is not known for the restriction of the conditions, and to solve this problem a numerical analyses of gas flow in one of the cabins under microgravity environment are carried out
由於實驗條件及實驗原理的限制，不能從總體上了解整個密封艙內的流動情況，數值計算則可以彌補這一缺陷。
分享友人