ventilation load 中文意思是什麼
ventilation load
解釋
換氣負荷- ventilation : n. 1. 通風，換氣（法）；通風裝置。2. 發泄，發表；（問題的）公開討論；訴諸輿論。
- load : n 1 裝載，擔子；負擔；工作（負荷）量。2 （車船等的）裝載量；一馱，一車，一飛機。3 【電、機】（機...
-
On the fact of turbine burn down failures and forced to be operated in limited load caused by high generator temperature rising, this paper analyzed the cause from electric magnetic design and ventilation type, provided improvement method and make it be implemented on no. 1 and no. 2 unit and got remarkable effect
針對瀏陽市株樹橋水電廠發電機溫升過高，以至多次發生發電機燒壞事故，被迫限負荷運行的實際狀況，從電磁設計和通風方式上分析了發電機溫升高的原因，提出了改造措施並加以實施，成功地電廠1號和2號機進行技術改造，取得了顯著的效果。 -
Considering that the characteristics of our country ' s highway tunnels are always of long spans, tabular and of various geometry, by means of thorough analysis of the different problems existed in the design of support structures of the tunnels at present, this paper pays special attention to the two key problems, optimization method of form selection of structural section of the tunnel as well as the stability and bearing capacity of the support structures, in the design of the long and large tunnel on high - class highway, introduces the simplified complex - form optimum method in the structure optimization theory, discusses the optimum design model of lining section of highway tunnel with satisfying demands in building clearance, ventilation and load conditions, puts forward an optimization method of form selection of three different kinds of lining sectional forms ( i. e. single - center circle, three - center tabular circle and three - center sharp circle ), establishes a complete set of systematic optimum design the ory and method of long and large tunnel on high - class highway, develops the corresponding computer software used on the planned xuefeng mountain highway tunnel on shaoyang to huaihua expressway in hunan province for optimization of form selections of the structural sections, and obtains a series of relatively reasonable structural design parameters
本文針對我國公路隧道多為大跨度、扁平、幾何形狀呈多樣化的特點，通過深入分析目前隧道支護結構設計中存在的各種問題，抓住高等級公路長大隧道設計中隧道結構斷面的優化選型及隧道支護結構的穩定性與承載能力兩個核心問題，引入結構優化理論中的簡易復合形優化方法，深入探討了滿足建築限界、通風條件、受力狀態約束等條件下公路隧道襯砌斷面優化設計模型，提出了三種襯砌斷面形狀（單心圓、坦三心圓和尖三心圓）的優化選型方法，建立起一套完善的高等級公路長大隧道的系統優化設計理論與方法，並開發出相應的計算機程序，用於擬建的上海至瑞麗國道主幹線湖南省邵陽至懷化高速公路雪峰山長大高速公路隧道的結構斷面優化選型，得出了一系列較為合理的支護結構設計參數。 -
Firstly, system cooling load, ventilation flux and thermal and humid processing were calculated and its feasibility was showed from the temperature, humidity of indoor air and fresh air flux
首先進行了系統的負荷、通風量及熱濕處理計算，從室內空氣溫度、濕度和新風量三個方面說明其可行性。 -
Large - scale machines employed in the construction to load and transport rocks also increase poisonous gases produced per hour. so the ventilation of the tunnel itself becomes a new problem
為實現快速施工，該隧道採用大型機械裝碴、運輸，這些機械單位時間內產生有毒、有害氣體增多，通風較為困難。 -
Presents the characteristics of recreational natatoria, discusses the modes of hvac systems, heat and moisture load calculation, ventilation rate determination and winter ventilation operation adjustment, and provides two calculation methods of outdoor humidity ratio in transition seasons
摘要介紹了娛樂性游泳館的特點，探討了暖通空調系統形式、熱濕負荷計算、通風量確定、冬季通風運行調節等問題，提出了兩種過渡季室外含濕量計算方法。
分享友人