warpage 中文意思是什麼
warpage
解釋
變形-
Heating warpage test
加熱翹幽試驗 -
Abstract : thermally induced stress and the relevant warpage cause by inappropriate mold design and processing conditions are problems that confounded the overall success of injection molding. a thermorheologically simple thermoviscoelastic two - dimension material model is used to simulate the residual stress and warpage within injection molded parts generated during the cooling stage of the injection molding cycle. the initial temperature field corresponds to the end of the filling stage. the fully time - dependent algorithm is based on the calculation of the elastic response at every time step. numerical results are discussed with respect to temperature and pressure
文摘:不均勻的熱殘余應力及其變形是注塑成型加工中常見的工程問題之一.應用熱流變簡單材料的二維熱粘彈本構方程得到的遞推公式，數值模擬了成型中的熱殘余應力及其翹曲變形，並用數值實驗討論了溫度、壓力對注塑件殘余應力及變形的影響，發現溫度變化不均勻是注塑件翹曲變形的最主要原因，其影響遠大於壓力的作用，與工程實驗的結論一致 -
Computer aided engineering in the field of injection molding can help us to minimize the warpage and other molding related defects by calculating the deformation accurately produced in plastic parts under the given injection molding conditions and optimizing the process
注塑模cae軟體能夠計算出特定工藝條件下製品的較為真實的變形結果，並為注塑成型提供優化的注塑工藝參數。 -
Test method for measuring warpage of ceramic tile
測量瓷磚撓曲度的試驗方法 -
Method of measuring warpage of refractory bricks
耐火磚的翹曲測量方法 -
Numerical simulation of warpage of injection - molded parts
注塑製品翹曲變形數值分析模型 -
Experimental research of warpage of hdpe injection molded plate
高密度聚乙烯平板翹曲變形實驗研究 -
Under certain conditions, the calculating formula of interlayer stress and the stress - distributing diagram in cut planes are provided, and the mathematical model for warpage deformation calculation is also established
建立了翹曲變形的數學模型，討論了各種工藝參數（層數、掃描線長、成型室溫度、層厚等）對翹曲變形量的影響。 -
The present study is focused on exploring the reasons of huge warpage and how to reduce it for pa66 / gf30. the wrong orientation of glass fiber causes the warpage ; however, remodeling the gate and increasing the wall thickness can cause the glass fiber to settle in the right orientation
本文分析了pa66 / gf30製品產生翹曲變形的原因是由於玻璃纖維的取向不合理，通過改變澆口和增加製品的壁厚可以改變玻璃纖維的取向從而有效降低翹曲變形量。 -
Huge warpage of molded parts has puzzled plastic molding companies at all the times
注塑製品的變形過大一直是困擾模具企業的一大難題。 -
Study of recordable optical disc warpage
翹曲的研究 -
Analysis and application of warpage for injection product
注塑產品的翹曲分析及改進 -
Curbing dvd warpage
翹曲控制 -
Standard practice for safeguarding against warpage and distortion during hot - dip galvanizing of steel assemblies
在鋼組合件熱浸鍍鋅時抗扭曲和變形的安全措施標準實施規程 -
During the fabrication or service, if the applied tensile stresses exceed the probabilistic tensile strength of silicon, then failure will occur. even a tiny crack will bring tremendous damage to devices and circuits. especially nowadays, with the increasing of silicon wafer diameter, warpage in heat treatment, defects and dislocations generated in silicon often become critical problems in ulsi devices fabrication
特別在大規模集成電路與器件生產中，一個微小的裂紋就可能導致后道工序中電路與器件的完全損壞；而且在熱處理過程引起的翹曲，使光刻精度下降；在矽片內部產生的氧沉澱及位錯等缺陷，會導致集成電路或器件的漏電流增加，使器件失效。 -
Keeping in view the warpage results obtained by numerical simulation, we can compensate it along the reverse direction and create a new model to be injection molded
藉助于數值化模擬分析的結果，將變形量逆向補償到產品模型中，將為降低製品的變形提供一個新的思路。
分享友人