water piping fittings 中文意思是什麼

water piping fittings 解釋
水管吊支架
  • water : n 1 水；雨水；露；〈常作 pl 〉 礦泉，溫泉；藥水。2 〈常 pl 〉水體；水域；水道；海；湖；河；海域；...
  • piping : adj 1 吹笛的；發銳音的，高調子的；滾熱沸騰的。2 溫和的，平靜的。adv 滾熱地。 be piping hot 滾熱的...
  • fittings : （房屋內的）設備,裝置,傢具
  1. Plastics piping systems for the transport of water intended for human consumption - migration assessment - determination of migration values of plastics pipes and fittings and their joints

    用於輸送供人消耗用水的塑料管道系統.析出物滲移量的車測定.塑料管道管件和連接件的析出物滲移量的測定
  2. Pvc - u. plastics piping systems for water supply - unplasticized poly vinyl chloride - fittings

    供水塑料管道系統.非增塑的聚氯乙烯
  3. Plastics piping systems for buried and above - ground pressure systems for water for general purposes, drainage and sewerage - polyethylene - fittings

    一般用途排水和排污水的地下或地面壓力系統用塑料管道系統.聚乙烯.配件
  4. Install the water piping and fittings as shown in figure 6

    按照圖6所示安裝水管線和連接件。
  5. Install the water piping and fittings as shown in figure 2

    按照圖2所示安裝水管線和連接件。
  6. Install the water piping and fittings

    安裝水管線和連接件。
  7. Thermoplastics piping systems - end - load - bearing joints between small diameter pressure pipes and fittings - test method for leaktightness under internal water pressure, including end thrust

    熱塑管道系統.小直徑壓力管和配件間端部負荷軸承接頭.在包含端推力的內部水壓下密封性的試驗方法
  8. Plastics piping systems. thermoplastics pipes and fittings for hot and cold water. test method for the resistance of mounted assemblies to tempetarure cycling

    塑料管道系統.冷熱水輸送用熱塑性管和配件.安裝組件溫度循環試驗方法
  9. Cooling water 810 tons, pneumatic supply 450 square meters. clarified water 9o tons. piping and fittings should be treated before installing for purpose of quality, more then 5, 0110 tons with largest clipper 1. 0 30 tons

    配管：製程中冷卻水8l0噸空氣450m3純水90噸等配管，管件須加潔凈處理，以提高映像管品質。
  10. Cooling water ( 810 tons ), pneumatic supply ( 450 square meters ). clarified water ( 9o tons ). piping and fittings should be treated before installing for purpose of quality, more then 5, 0110 tons with largest clipper 1. 0 ( 30 tons

    配管：製程中冷卻水（ 8l0噸） 、空氣450m3 、純水（ 90噸）等配管，管件須加潔凈處理，以提高映像管品質。
  11. All piping and fittings must be suitable for use with potable water and meet the requirements of local codes

    所有管道和連接件必須適用於使用生活用水，並符合當地規程的有關要求。
  12. Piping and valves maintenance, drainage systems maintenance, heating systems maintenance, sanitary fittings maintenance, water tanks maintenance, etc

    喉管與閘閥維修、渠務系統維修、供熱系統維修、衛生設備維修、水缸維修等
  13. Polypropylene piping systems for hot and cold water installations - part 3 : fittings

    冷熱水用聚丙烯管道系統第3部分:管件
  14. Plastics piping systems - thermoplastics pipes and associated fittings for hot and cold water - test method for resistance of joints to pressure cycling

    塑料管道系統.熱水和冷水用熱塑件和相關配件.接頭耐壓力循環的試驗方法
  15. Plastics piping systems - thermoplastics pipes and associated fittings for hot and cold water - test methods for resistance of joints to pressure cycling ; german version en 12295 : 1999

    塑料管道系統.熱水和冷水用熱塑性塑料管和相關管件
  16. Thermoplastics piping systems ; end - load bearing joints between small diameter pressure pipes and fittings ; test method for leaktightness under internal water pressure, including end thrust ; german version en 715 : 1994

    熱塑塑料管道系統.小直徑壓力管和管接頭之間承載端部
  17. Thermoplastics piping systems. end - load bearing joints between small diameter pressure pipes and fittings. test method for leaktightness under internal water pressure, including end thrust

    塑料管道系統.小直徑壓力管與配件間的端負荷軸承連接.包含軸向推力的內部水壓下密封性試驗方法
  18. Polybutylene piping systems for hot and cold water installations - part 3 : fittings

    冷熱水用聚丁烯pb管道系統第3部分：管件
  19. Plastics piping systems for hot and cold water installations - polybutylene - fittings

    冷熱水裝置用塑料管道系統.聚丁烯.配件
  20. Pb. 3 : plastics piping systems for hot and cold water installations - polybutene - part 3 : fittings

    冷熱水裝置用塑料管道系統.聚丁烯
分享友人
分享到 Line

分享到臉書