weld 中文意思是什麼

音標 [weld]
weld 解釋
n. 名詞 焊接（點），熔接點。
vt. 及物動詞 焊[熔]接；使密切接合，結合。
A welded joint 【機械工程】熔接頭。
vi. 不及物動詞 被焊接[熔接]。
Welding powder 焊粉。
A welding rod 焊條。
Gas welding 氣焊。
Resistance weld 電焊。
A weld-less pipe 無縫管。
n. 名詞 -er 1. 焊工。
2. 焊接機。
n. 名詞 【植物；植物學】淡黃木樨草；（由淡黃木樨草採取的）黃色染料。

  1. The etched section also reveals that multiple weld passes were made over the top of the original submerged arc weld pass.

    從酸蝕斷面還可以看出：在原自動埋弧焊的上面覆蓋有多層焊道。
  2. Abstract : for analyzing the residual stress distributing state within the weld joint, and its effect on the performance of welding structure, when welding the ferrite pearlite steel with the austenite steel, this paper develops a finite element program to compute the interface stress of two or over two material. finally, this program is used to analyze the mechanical behavior of heterogenic joint

    文摘:為了分析鐵素體、珠光體類鋼與奧氏體類鋼焊接時，焊接接頭處焊接殘余應力的分佈狀態及其對焊接構件性能的影響，研製了可計算兩種或兩種以上材料界面應力的有限元程序，並用此程序分析了異質接頭的力學行為。
  3. This indicated that the fracture had initiated at the unfused butt weld in the longitudinal stiffener.

    研究表明裂紋是從縱向加勁助未熔透的對接焊縫中起始的。
  4. Some crack extension probably developed from the unfused section of the butt weld across the thickness of the stiffener during transport and erection.

    有些裂紋可能在運輸和安裝過程中就從加勁肋對接焊未熔透處開始發展。
  5. Butt weld neon lamp - neon lamp jiangsu bright group

    電焊接氖燈-指示氖燈伯樂達國際商務網
  6. Butt weld neon lamp neon lamp - jiangsu bright group

    電焊接氖燈指示氖燈-伯樂達國際商務網
  7. September 1994, dagstuhl castle, germany, pp. 134 - 137. 10 tatarinov i, ives z g, halevy a y, weld d s. updating xml. in

    Xupdate是一個xml更新語言，它是w3c的一個工作草案，允許用戶建立插入更新和刪除元素和屬性。
  8. Fourth, the paper treats two kinds of hoisting projects of high alititude construction in bulk and member assembly, hositing machine and plan layout, setting up scaffold and joints, and installing trunks, branches and joints etc. then in detail discusses the method which applys total station to measure three - dimensional coordinate of dendriform structure, including selecting survey sign points, creating survey system and converting survey coordinate system etc. the paper also deep research on the welding performance, welding method, welding process, welding stress and control, welding strain and rectification, weld defects analysis and weld quality inspection, and so on complicated heterogeneity steel weld proplems

    接著系統的論述了高空散裝法和分單元安裝法兩種樹狀結構吊裝方案，樹狀結構吊裝機械及平面布置，樹狀結構胎架及節點的搭設，以及樹狀結構樹干、樹枝和節點的吊裝工藝等諸多工藝問題。詳細的論述了採用全站儀對樹狀結構進行空間三維坐標測量的方法，包括測量標志點的選取、測量系統的建立及測量坐標的轉換等問題。深入地研究了樹狀結構可焊性、焊接方法、焊接工藝、焊接應力及控制、焊接變形及矯正、焊接缺陷分析及焊接質量檢查等復雜的異種鋼焊接問題。
  9. A kind of stainless steel flux - cored wire has been successfully developed, based on acid slag type system, by adding a bit of oxides and trace of deoxidizer, adjusting the fluidity of melting slag to increase shielding of the back weld

    在酸性渣系的基礎上，通過添加少量氧化物，調整熔渣的流動性，並加入微量的強脫氧劑，以增強背面焊縫的保護，研製成功一種背面不充氬的不銹鋼打底單面焊雙面成形專用藥芯焊絲。
  10. Standard methods for determination of the diffusible hydrogen content of martensitic, bainitic, and ferritic steel weld metal produced by arc welding

    測定馬氏體貝氏體和鐵素體鋼電弧焊接金屬中可擴散氫含量的標準方法
  11. Weld drive shaft tube assembly

    傳動軸管焊接合件
  12. Weld proce - dure specifications wps

    焊接工藝規程
  13. Forming process analysis of equiaxed grain in weld nugget zone during friction - stir welding of aluminum alloy

    鋁合金攪拌摩擦焊接頭焊核區等軸再結晶組織的形成機制
  14. Method of fillet weld test for welding consumables

    焊接消耗品用角焊試驗的方法
  15. Test method for weld strength of getter support

    吸氣劑支架焊接強度測試方法
  16. Hard facing is weld deposited cobalt base alloy

    硬面焊接鈷基合金沉澱物。
  17. Metallographic examination for weld seam of nuclear fuel rod used in pwr

    壓水堆核燃料棒焊縫金相檢驗
  18. Oblique angle fillet weld

    斜角角焊縫
  19. As an application of this fem preprocessing system, the simulation on the welding process of missile ’ s oil box was performed, in which the effects of the welding sequences of four web plates and welds on each web plate are primarily analyzed. the simulation results show that the deformations under varied welding sequences are almost the same. downward deflection deformation is obtained along the weld longitudinal direction in the structure as well as upward deflection deformation along the weld traverse direction

    對于某型號導彈油箱結構焊接過程的數值模擬計算，主要考察了每塊立板上各段焊縫焊接順序的調整、四塊立板之間不同的焊接順序以及焊接起始端的選擇對結構焊后變形的影響規律，模擬結果表明:壁板在各種焊接順序下的整體變形規律基本相似，即焊後壁板沿焊縫縱向發生了向下的撓曲變形，中部向下變形量最大;沿焊縫橫向發生了向上的撓曲變形，壁板兩端部變形量較大，且壁板前端變形大於壁板後端。
  20. Dye penetrant examination of the completed weld

    對已完成的焊縫進行著色滲透檢測。
分享友人
分享到 Line

分享到臉書