zero correction 中文意思是什麼

zero correction 解釋
零點校正；零點差修正
  • zero : n （pl zeros zeroes）1 【數學】零；零號。2 零位；零點，起點；（溫度表的）零度，冰點；座標原點；無...
  • correction : n 修正，改正；校正；矯正；〈古語〉懲罰；勘誤表，補正。 a copy disfigured by numerous corrections ...
  1. Based on an analysis of the major factors affecting the quality of data obtained in aeroelectromagnetic survey, this paper has put forward zero horizontal drift correction methods such as field value standardization and phase check and correction, studied and developed a suite of techniques suited to data - processing and graphical representation for aeroelectromagnetic method

    摘要在分析探討影響航空電磁測量數據質理主要因素的基礎上，提出了場值標定，相位校驗改正等零水平漂移改正方法，研究開發了一套適合航空電磁法數據處理與圖示的方法技術。
  2. Software design realizes functions of flow characteristic correction, automatic zero setting, span setting, alarm, fault diagnosis and field display ; 4

    3 、軟體設計實現了流量特性修正、自動調零、調量程、報警、故障自診斷、現場顯示等功能。
  3. Influence of dc - rail zero - voltage notch on the output of the inverter is investigated, and an important conclusion is obtained that the direction of output current of the inverter is not effected by the voltage deviation produced by dc - rail zero - voltage notch, on the basis of which, a new simple correction approach is put forward. experiment results show that the proposed correction method is effective

    探索了直流母線零電壓凹槽對逆變器輸出特性的影響，得出了母線零電壓凹槽形成的輸出電壓偏差與逆變器輸出電流方向無關這一重要結論，在此基礎上，提出了一種簡便的校正新方法，通過試驗驗證了該校正方法的有效性。
  4. The research results are controlled source which has linear or nonlinear variabe frequency scan function and the seismic instruments which match with it, and the method of small group intervals, small offset, much more channels, short array length, high - frequency receivers are applied during the link of data acquisition, and that the techniques of the refraction static correction, the noise suppressing, the high - resolution velocity analysis, the wavelet length compression, the wavelet zero - phase, and the prestack migration should be applied emphasizedly during the link of data processing and interpretation

    研究表明，對于城市活斷層的抗干擾高解析度淺層地震勘探，在數據採集環節應採用具有線性或非線性變頻掃描功能的可控震源和與其相匹配的地震儀器，以及小道間距、小偏移距、多接收道、短排列和高頻檢波器接收的工作方法；在數據處理與解釋環節，要重視折射靜校正技術、噪聲壓制技術、高精度速度分析技術、子波壓縮技術、子波零相位化技術和疊前偏移技術等的應用。
  5. A resolution method in software is applied to calibrate zero point and full scale of the circuit. software approach to nonlinear correction for sensor and circuit is presented. therefore system error is eliminated, and measurement accuracy of temperature is improved. the signal of acidity electrode is detected by a differential amplifier circuit, which consists of operational amplifiers tlc2254 with high input impedance and low drift

    採用橋路和單運放差動放大電路對溫度傳感器信號檢測放大，軟體校正溫度傳感器和測量電路的非線性，軟體校準測量電路的零點和滿度，消除測量電路的系統誤差，提高補償溫度的測量精度；採用高阻、低漂移運放tlc2254組成高阻差動放大電路用於酸度電極信號測量。
  6. In this article the author emphasizes to use advantage quality control technology to analyze problems exist in product and process, to give out correction methods and measure. enhance process control using analysis technique, well designed quality plan, introducing information management system and finally introducing 6 sigma theory to totally improve product quality, reach zero defaults and reduce quality costing

    文章中運用先進的質量管理技術，分析產品或工序中存在的問題，提出解決問題的方法和糾正措施；加強過程式控制制，應用先進的統計技術，使工序處于受控狀態；實施質量策劃，進行質量改善；引入信息管理系統，為質量管理提供技術支持。
  7. Correction of zero drift

    零漂改正
  8. Remedy : check zero point correction of the star and re - adjust if necessary

    方法：檢查零點位置是否正確，並且需要時，加以調整。
  9. The experience results indicated the reliability of this kind of thermostatic control system. the analysis and compare about modern dielectric loss measuring methods are presented on chapter 3, and the zero - crossing testing phase discrimination method is adapted as the measuring method of this measuring system. furthermore, applied high frequency pulse technique, channel self - correction technique, anti - harmonic technique are used to increase accuracy and reliability of measurement

    本文對現代介質損耗測量技術進行了分析與比較，採用過零鑒相比較法作為介質損耗測量方法，並結合外施高頻脈沖技術、通道自校正技術、抗諧波技術，設計了高精度介質損耗測量電路，有效提高了介質損耗測量的精度，減小了測量誤差。
  10. The working principle of buck - boost is first introduced, and averaging model of non - ideal buck - boost converter is established. the design details for voltage loop were given and zero - pole compensation method from classic control theory was applied to the filed of power electronics. thus, small - signal model of closed - loop was established, with detailed design guidelines for correction network

    本文介紹了buck - boost電路的工作原理，建立了非理想buck - boost平均法的模型，對整個電路進行了單電壓閉環參數設計的研究，實現了控制理論中零極點補償法在電力電子中的應用，建立了閉環小信號模型，總結了設計校正網路的步驟和具體方法。
分享友人
分享到 Line

分享到臉書