zero order mode 中文意思是什麼

zero order mode 解釋
零階模
  • zero : n (pl zeros zeroes)1 【數學】零;零號。2 零位;零點,起點;(溫度表的)零度,冰點;座標原點;無...
  • order : n 1 次序,順序;整齊;(社會)秩序,治安;狀況,常態;健康狀態;條理;會場秩序;議事程序,日程;...
  • mode : n 1 法,樣,方法,方式。2 模,型;樣式,體裁,款式;習慣。3 風尚;〈the mode〉流行,時髦。4 【語...
  1. The third part : according to the verified structural damage identification method and supposing the to - be identified parameters to be independent and have normal distribution, the scheme of identifying bridge structure damage is proposed by using the probability damage identification method. assume the zero - order, the first - order and the second - order perturbation statistics of the frequencies and the mode shapes of the bridge structures are known, and substitute them into the statistics property formulas of the frequencies and the mode shapes, as a result an objective function including the mean values and the variance of all the identified parameters is established. set

    對于連續梁橋,當損傷位置位於跨中附近時,大多數無損傷單元的損傷概率均在10 %左右,可作為小概率事件,不發生損傷,但與損傷單元相鄰的無損傷單元,其損傷概率達到20 %以上,很難被排除,只有對這些單元進行二次識別,才能得到比較可靠的計算結果;如果損傷位於支點附近時,則不會出現上述情況,對于無損傷單元,損傷概率都小於10 % ,不發生損傷,損傷識別結果
  2. The thesis has done the widespread investigation and study to the domestic and foreign ’ s technologies of analogy low voltage and low power, and analyzes the principles of work, merts and shortcomings of these technologies, based on the absorption of these technologies, it designs a 1. 5v low power rail - to - rail cmos operational amplifier. when designing input stage, in order to enable the input common mode voltage range to achieve rail - to - rail, it does not use the traditional differential input pair, but use the nmos tube and the pmos tube parallel supplementary differential input pair to the structure, and uses the proportional current mirror technology to realize the constant transconductance of input stage. in the middle gain stage design, the current mirror load does not use the traditional standard cascode structure, but uses the low voltage, wide - swing casecode structure which is suitable to work in low voltage. when designing output stage, in order to enhance the efficiency, it uses the push - pull common source stage amplifier as the output stage, the output voltage swing basically reached rail - to - rail. the thesis changes the design of the traditional normal source based on the operational amplifier, uses the differential amplifier with current mirror load to design a normal current source. the normal current source provides the stable bias current and the bias voltage to the operational amplifier, so the stability of operational amplifier is guaranteed. the thesis uses the miller compensate technology with a adjusting zero resistance to compensate the operational amplifier

    本論文對國內外的模擬低電壓低功耗技術做了廣泛的調查研究,分析了這些技術的工作原理和優缺點,在吸收這些技術成果基礎上設計了一個1 . 5v低功耗軌至軌cmos運算放大器。在設計輸入級時,為了使輸入共模電壓范圍達到軌至軌,不是採用傳統的差動輸入結構,而是採用了nmos管和pmos管並聯的互補差動輸入對結構,並採用成比例的電流鏡技術實現了輸入級跨導的恆定;在中間增益級設計中,電流鏡負載並不是採用傳統的標準共源共柵結構,而是採用了適合在低壓工作的低壓寬擺幅共源共柵結構;在輸出級設計時,為了提高效率,採用了推挽共源級放大器作為輸出級,輸出電壓擺幅基本上達到了軌至軌;本論文改變傳統基準源基於運放的設計,採用了帶電流鏡負載的差分放大器設計了一個基準電流源,給運放提供穩定的偏置電流和偏置電壓,保證了運放的穩定性;並採用了帶調零電阻的密勒補償技術對運放進行頻率補償。
  3. Reactive power are calculated using the new algorithm. on the basis of analyzing different kinds of control strategies of var compensation, the paper applies the criterion of voltage and var to control switching and illustrates a improved mode of switching capacitor which can prevent the switched - capacitor from the impacting of instantaneous rush currents by means of zero - crossing triggering of scr components, and can realize auto - tracking var and auto - switching shunt capacitor bank. initial operating parameters are stored in information flash memory of the mcu using flash self - programming technique in order to decrease complexity of the circuit and improve stability

    高壓智能無功補償控制器以flash型16位單片機msp430f149為控制核心,採用了一種相角實時測量的新演算法,並在此基礎上計算出了功率因數、有功和無功,減少了運算量提高了精度;在分析了各種無功補償控制策略的基礎上,以母線電壓和無功功率復合判據控制投切,並提出一種改進的電容器投切方式? ?暫態投切控制晶閘管過零觸發,避免了電容器投切時的電流沖擊;穩態運行時接觸器替代晶閘管,實現無功補償的自動跟蹤和電容器的自動投切,解決了投切時的暫態電流沖擊和穩態時可靠運行的難題;控制器的原始運行參數採用flash自編程技術,將其保存在msp430f149片內的信息flash中,簡化了硬體電路,大大提高了系統的可靠性。
分享友人