zero voltage current 中文意思是什麼
zero voltage current
解釋
零壓電流-
A novel phase - shifted zero - voltage and zero - current switching pwm dc / dc full - bridge converter is presented in this thesis, which is based on the groundwork of summarization of the development of power electronics in recent years and lucubration in theoretical basis of modern high frequency soft switching power convert technique and analysis of operation principle, characteristic of the circuit and inherent drawbacks of the traditional phase - shifted zero - voltage switching pwm dc / dc full - bridge converter
本文在對近年來電力電子學科的發展高度綜述和對現代高頻軟開關功率變換技術理論基礎深入研究的基礎上，對傳統的移相控制zvspwmdc dc全橋變換器的工作原理、電路特性、存在的缺點進行了分析，在此基礎上提出了一種改進型的移相控制zvzcspwmdc dc全橋變換器。 -
The mutual inductor of electric current and voltage mutual inductor play an important role in relay protection. prevent from ct differential to protect and miss movement an important subject that the generatrix is protected on the saturation, put forward two electric current pass zero hour linear to spread person who become put into differential to protect in ct in recent years, avoid ct saturation district, can judge the bus bar trouble correctly
但是在母線區外發生短路故障（特別是故障電流含有大量非周期分量）時， ct會出現飽和現象， ct飽和后，不能正確地傳變一次側電流，從而使二次電流發生嚴重畸變，產生很大的差電流，這樣就容易引起誤動作。防止ct飽和時差動保護誤動作一直是母線保護的一個重要課題，近年來提出的在ct二次電流過零時的線性傳變區投入差動保護，避開ct飽和區，能對母線故障做出正確判斷。 -
Voltage segment network constituted by electron switch of bta and controlled by single chip microcomputer constitutes a new fast electronic regulator. for bta cross zero touch off, sine wave which is exported is integrity. a new way to generate stable ac current is found with feed back control system by single chip microcomputer. so a new high power ac current regulator is developed
採用單片機控制雙向可控硅作為電子開關所組成的電壓分節網路，組成新穎快速的電子調壓器；由於雙向可控硅過零觸發，所以其輸出是不失真的完整正弦波；再用單片機組成反饋控制系統，從而找到了交流穩流的新方法，研製出一個大功率交流穩流電源 -
( 4 ) the experiment of asymmetrical half bridge converter design and the result of it base of the above analysis, the dc / dc converter is designed, it is proved that asymmetrical half bridge can realize zero voltage switching when it satisfies the condition of load current and deadtime by the experiment
（ 4 ）不對稱半橋的實驗電路設計及實驗結果基於前面的分析，設計了一個不對稱半橋dc dc變換器的實驗電路，進行了實驗研究，實驗結果證實了在滿足死區和負載電流兩個條件時，不對稱半橋可以實現零電壓開關。 -
Conventional hard switching technology has several flaws below : on and off loss, inductive off, capacitive on and diode recover problems. comparing with it, the loss of on and off decreases markedly, as the switches are on and off in zero voltage or zero current cases. and also the size of converter becomes smaller because of the higher of switching frequency
傳統硬開關技術由於存在開通關斷損耗大、感性關斷、容性開通、二極體反向恢復等問題，與之相比，軟開關技術在零電壓或零電流條件下導通，開關損耗明顯降低，加上開關頻率的提高使得變換器的體積得以減小，這也是軟開關技術受到青睞的原因。 -
The device can protect start - up status and running status of asynchronous motors by differential protection, over current protection, negative - sequence current protection, zero - sequence current protection, inverse time current protection, under - voltage protection and so on, can measure every kind of electricity, and can process the function of telecontrol, telemetering and telecommunication
其依靠電流差動、速斷、負序過流、反時限、零序過流和低電壓等保護方法實現了片電動機的運行、啟動和自啟動過程進行保護，並實現各種電量的計量，同時具有遙控、遙測、遙信的功能。 -
Influence of dc - rail zero - voltage notch on the output of the inverter is investigated, and an important conclusion is obtained that the direction of output current of the inverter is not effected by the voltage deviation produced by dc - rail zero - voltage notch, on the basis of which, a new simple correction approach is put forward. experiment results show that the proposed correction method is effective
探索了直流母線零電壓凹槽對逆變器輸出特性的影響，得出了母線零電壓凹槽形成的輸出電壓偏差與逆變器輸出電流方向無關這一重要結論，在此基礎上，提出了一種簡便的校正新方法，通過試驗驗證了該校正方法的有效性。 -
( 2 ) each state of the total switching period has been studied in detail, in which the voltage of block capacitor and current of leakage inductance of main transformer and keeping time of each state have been discussed, then the condition of zero voltage switching is attained, which gives theory guidance for setting reasonable dead time, finally, the possibility of zero voltage switching is proved by simulation of saber software
（ 2 ）對不對稱半橋在一個完整的開關周期內各個狀態分析，描述了隔直電容電壓和變壓器漏感電流的變化規律，各個狀態的持，然後得出實現zvs的條件，從而為設置合理的死區時間提供了理論指導，最後用saber軟體進行了模擬，驗證了零電壓開關實現的可能性。 -
Explicit description of main circuit topology, operation principle, characteristic of the circuit of the novel phase - shifted zero - voltage and zero - current switching pwm dc / dc full - bridge converter as well as the simulation analysis with the pspice software is proposed
對移相控制zvzcs下pwm的dc dc全橋變換器的拓撲結構、工作原理和電路特性作了深入的闡述，採用pspice軟體進行了計算機的模擬分析。 -
According to the mechanism characteristics of the ac motor, with zero - voltage switching technology, the pdm converter mathematical models both the pwm and rectangular wave control mode are given in this paper. and the voltage and current harmonic analysis and the simulation waveforms of the output voltage, current and power are also described respectively
根據交流電機在恆轉矩區和恆功率區的特性，結合零電壓開關技術，分別給出相應的脈寬調制控制（ pwm ）方式和方波控制方式下的高頻交流脈沖密度調制變頻器的數學模型，電壓和電流的諧波分析以及輸出電壓、電流和功率的模擬波形。 -
" soft switching " is zero voltage switching or zero current switching, which the voltage ( or current ) of the switch varies by law of sine or quasi sine, the switch is on when its voltage reaches zero ( or switch is off when its current reaches zero ) by resonance. it makes switch loss is zero, so it can increase the operating frequency and raise power density, minimize the size of transformer and inductor
「軟開關」是指零電壓開關或零電流開關，它是利用諧振原理，使開關變換器的開關管電壓（或電流）按正弦（或準正弦）規律變化，當電壓過零時，使器件開通（或電流自然過零時，使器件關斷） ，實現開關損耗為零，從而提高開關頻率，減小變壓器、電感的體積。 -
The scheme of realizing soft - switching can be found, at the same tune, the concepts of the leading switches and the lagging switches are presented. two kinds of soft - switching methods, zero - voltage - switching ( zvs ) and zero - voltage and zero - current - switching ( zvzcs ), can be classified on the base of realizing soft - switching of the lagging switches
在對其控制策略的研究中，找出了可以實現軟開關的方案；同時提出了超前管和滯后管的概念，根據滯后管實現軟開關的方式，將變換器的軟開關方式分為兩類：零電壓開關方式和零電壓零電流開關方式。 -
Among them, phase shifted ( ps ) full bridge ( fb ) zero - voltage - switched ( zvs ) pulse - width - modulated ( pwm ) dc / dc converter has strong competitive power in big power capacity fields. but it has some limitations such as smaller load range with zvs and larger circulation energy. the ps - fb - zvs - pwm dc / dc converter with a saturable inductor utilizes saturable inductor s critical saturable current characteristic and storage energy, to enlarge load range with zvs and improve output efficiency under light load
其中，移相控制零電壓開關脈寬調制dc / dc全橋變換器在大容量領域很有競爭力，但它具有實現零電壓開關負載范圍小，循環能量大等限制，帶飽和電感的移相控制零電壓開關全橋變換器利用飽和電感的臨界飽和電流特性及儲能，來擴大零電壓開關（ zvs ）的負載范圍，提高輕載時的輸出效率，具有非常重要的研究價值。 -
On the basis of theory and simulation analysis, the design, execution and experimental study of the phase - shifted zero - voltage and zero - current switching pwm dc / dc full - bridge converter is fulfilled
在理論和模擬分析的基礎上，對新型移相控制zvzcspwmdc dc全橋變換器進行了設計、製作及實驗研究。 -
The problem is much more critical when the inverter frequency is high. in a welding machine, the main circuit with the technology of the soft - switching is much idealer than the hard - switching. firstly of all, by the theory of the soft - switching, this paper relatively analysis the advantages of the soft - switching and, with the help of the simulation software pspice, analyzes the main circuit of the full bridge shift - phased zero voltage zero current ( zvzcs ) soft - switching
結合軟開關實現原理，本文首先對比分析了軟開關在提高效率、降低emi干擾等方面的技術優勢，通過pspice軟體模擬，分析研究了全橋移相零電壓零電流（ zerovoltagezerocurrent - - - - zvzcs ）軟開關電路，詳細介紹了該電路的軟開關實現過程，並給出了電路模型和關鍵元件的設計參數。 -
When the motorcycle is braking or slowing down, the kinetic and / or potential energy is fed back to the battery, so the running distance can be extended and the energy efficiency is improved. an asynchronous motor is employed in this new system which can overcome the traditional dc drive system bugs and to reduce the cost and maintenance. in addition, the switches of dc / dc converter switch under zero current and zero voltage conditions, which can also reduce the switch losses, electro magnetic interference ( emi ) and prolong its life
該系統在功能上實現了車輛剎車減速或下坡制動時能量的回饋，達到節能、提高能量使用效率和增加車輛行駛距離的目的；採用交流異步電機，克服了傳統直流驅動系統的諸多缺陷，降低了成本，減少了維護；採用zczvs技術，降低了電磁干擾和損耗，提高了效率；另外，在逆變主電路中採用ipm模塊，簡化了系統結構，節約了空間，提高了整個系統的可靠性和經濟性。 -
Serial - parallel combined two - transistor forward converter is presented for high input voltage and high power application, and the operation principle of the topology is analyzed in this paper. all switches are turned off with zero voltage switching, and the two switches of them are turned on with zero current and zero voltage switching. the difference of input capacitances, conducting voltage drop of switches, duty cycle and windings of the transformer of the combined converter influences the voltage balance of the input capacitors
本文介紹了雙管正激變換器的兩種穩定工作狀態，詳細分析了帶lcd無損箝位網路的並?並組合式雙管正激變換器的工作原理，該組合式變換器中的開關管實現了零電壓關斷，並介紹了該電路拓撲的特點和lcd網路參數設計，採用pspice軟體進行了模擬和分析，最後，研製出一臺2 . 3kw樣機。 -
2. we present a novel de - rail parallel resonant zero voltage transition three - phase pwm voltage - source inverter which is based on resonant zero voltage ( zero current ) transition technique ; at the same time it ' s efficiency analysis and simulation result are presented. 3
把諧振過渡軟開關技術應用於直流環節逆變器得到了一種新的諧振過渡軟開關逆變器；論文對該新型諧振過渡軟開關逆變器進行了工作原理、效率分析並對主電路進行了模擬。 -
According to the present actual underground power system which neutral point is grounded through arc suppression coil in many supper big shaft, the development history and present situation of synthetic protection system used in hv flameproof switchgear are reviewed, and on the basis of analyzing the problems existed in high voltage flameproof switchgear, the selective leakage protective method based on the detecting harmonic direction of zero sequence current as well as the value of zero sequence voltage is proposed in this paper, and at the same time, harmonics extracting schematic and transforming circuit are also designed
本文深入系統地研究了基於intel80c196kb單片機控制的6kv防爆開關綜合保護系統，主要內容如下：針對大型及特大型礦井供電系統中性點普遍採用消弧線圈接地方式的現狀，回顧了國內外礦用高壓防爆開關保護系統的發展歷史，分析了目前國內高壓饋電開關保護系統所存在的問題，提出了「基於零序電壓基波啟動，五次諧波功率方向比較」的選擇性漏電保護原理，設計了相應的五次諧波提取電路和功率方向鑒別電路。 -
Numerical computation of the dynamic variation of the arc have been completed in the process of before current zero, after current zero and approaching zero to simulate the arc dynamic variation during the interruption process for the high voltage sf6 circuit breaker
對電流零前、過零期間以及零后的電弧動態變化進行數值求解，實現了高壓sf _ 6斷路器開斷過程電弧動態變化的模擬模擬。
分享友人