代替荷載 的英文怎麼說
中文拼音 [dàitìhézǎi]
代替荷載
英文
substitute load-
The layered combined finite element model is taken in the finite analysis of concrete and bonding bar. in the nonlinear analysis ofunbonded prestressed concrete, the effect that unbonded tendons acts on concrete is replaced by equivalent force in the method of equivalent prestress
在有限元分析中，混凝土和粘結鋼筋採用分層組合式的有限元模型，在無粘結預應力混凝土的非線性分析中，將無粘結預應力筋對混凝土的作用，借鑒預應力的荷載平衡法，用其等效力來代替預應力作用。( 3 ) it is known that load effect is not consistent with the section resistance incommon section continuous composite beam. a kind of composite beam with itsrational section size is suggested, which is consist of the t shape concrete beam andsteel girder. this kind of composite beam not only has enough carrying capacity, almost has same positive and negative resistance moment, but can decrease theamount of the steel
（ 3 ）分析可知連續組合梁的跨中、支座截面處荷載作用效應及截面抗力規律不匹配，本文提出了採用t形混凝土梁和工字鋼代替一般的混凝土板和工字鋼的組合梁截面形式，並給出了截面尺寸比例，能使正負截面抵抗矩接近，符合組合梁受力特徵，減少了材料用量，滿足承載力和剛度等要求。It consists of two parts : the first part ( chapter 2, 3, 4, 5 ) studies the characteristic of elastic waves and surface waves in orthotropic fluid - saturated porous media using biot ' s theory which is based on the substitutive model. in the second one ( chapter 6 ), a new three - dimensional meso - calculating model, which is more coincided with the inner action mechanism of porous media, is proposed. based on this model, the elastic wave propagation in fluid - saturated porous media under longitudinal impacting is discussed
論文主要分為兩大部分：第一部分基於替代模型的biot理論，對各向異性介質中平面波以及表面波的傳播特性進行了研究；第二部分從細觀層次出發，提出了一個更加符合含液飽和多孔介質內部作用機理的三維細觀計算模型，並對縱向沖擊載荷作用下液飽和多孔介質中彈性波的傳播規律進行了討論。3. it has been clarified that the design of ceramic rocker arm pertains to reverse design. with this understanding, this paper expatiated in detail on how to seek out the working loads and design parameters of the rocker arm in reverse order by employing computer aided reverse engineering ( care ) technology in place of the conventional calculation model
3闡明了陶瓷搖臂的設計屬于反設計，並詳細描述了運用計算機輔助反向工程（ care ）技術替代傳統的分析計算模型對氣門搖臂的工況載荷和設計參數進行反求的一般方法。3 ) the average - strain of cross - section still can be assumed to be keep - in - plane within the whole loading procedure ; the theoretical moment - curvatures obtained by the cross - section keep - in - plane is consistent with the experimental ones. 4 ) the analytical flexural bearing capacity and cfrp - strain are more accurate by assuming the concrete ultimate strain to be 0. 07 instead of 0. 0033 ; 5 ) limiting the cfrp - strain under 0. 01 is reasonable to evaluate the flexural bearing capacity of rc beams retrofitted with cfrp ; 6 ) the initial load is hardly influence the flexural bearing capacity of cfrp - strengthened rc beams
取混凝土的極限壓應變0 . 007代替0 . 0033進行計算的結果能更準確地評浙江大學碩士學位論文2004摘要價加固梁的抗彎承載力和cfrp應變; 5 .在計算cfrp加固梁的抗彎承載力時，限制cfrp的應變在0 . 01以內的措施是恰當的; 6 .梁所承受的荷載的大小對加固後梁的抗彎承載力影響不大。The formulas of the critical edge load and critical load are expanded from the two - dimensional stress state to the three - dimensional stress state by using smp ( matsuoka - nakai ) strength criterion to substitute for mohr - coulomb strength criterion, and the new formulas are proposed in chapter three
本文將臨塑荷載、臨界荷載計算公式擴展到三維應力狀態，應用smp （松崗?中井）強度準則替代莫爾?庫侖強度準則，推導了三維應力狀態下的臨塑荷載、臨界荷載計算公式。分享友人