內置爐膛鍋爐 的英文怎麼說
中文拼音 [nèizhìlútángguōlú]
內置爐膛鍋爐
英文
integral furnace boiler- 內 : 名詞1. （內部; 里頭; 里邊） inner; inside; within 2. （妻子或妻子的親屬） one's wife or her relatives 3. （姓氏） a surname
- 置 : 動詞1. （擱; 放） place; put; lay 2. （設立; 布置） set up; establish; arrange; fix up 3. （購置） buy; purchase
- 膛 : 名詞1. （胸腔） chest; thorax 2. （器物的中空部分） inside cavity; chamber
- 鍋 : 名詞1. （炊事用具） pan; pot 2. （裝液體加熱用的器具） boiler; cauldron3. （某些器物上像鍋的部分） bowl （of a pipe, etc. ）
- 內置 : build-in
- 鍋爐 : boiler; furnace
-
This thesis establishes the main factor of heating surface slagging of no. 1 boiler, that it is due to irrational layout of furnace heating surface, improper angle of burner which lead to flames attaching to furnace walls. such deduction is built on the basis of necessity of analyzing the heating surface slagging, the type of coal, the design of the furnace and burner, the operational condition and other factors effecting slagging of boiler. the research is mingled with practical operations of no. 1 boiler in inner mongolia fengtai electric power generation co, ltd
本論文從分析燃煤鍋爐結渣問題必要性出發，從煤種、爐膛及燃燒器設計、運行工況等因素對鍋爐結渣的影響著手，結合內蒙古豐泰發電有限公司~ # 1鍋爐實際運行中存在的問題，確定了~ # 1爐受熱而結渣的主要原因是爐膛受熱面布置不合理，燃燒器角度不合適導致火焰貼壁所致。This article aims at the boiler ' s problems in operation : 1 ) under nominal load, the smoke temperature at the outlet of hearth reaches 1200, far more exceeds 1050 the original designed temperature. this will always result in slag inside boiler and the temperature of overheater ' s pipe superheat, so that boiler cannot take nominal load and all these influence boiler ' s nomal operation heavily, 2 ) this article also studied the reason why the assistant oil becoming necessary when coal changes. during the nomal operation, many factors ( makeup of combustor and its disposal, smirch and encrust of water wall, excessive air coefficient, temperature of primary air, coal type and density of coal dust ) can deviate the designed working conditions, then affect the boiler ' s nomal operation
本文針對該鍋爐在實際運行中存在的問題：在額定負荷下，爐膛出口超溫、低溫段過熱器前煙溫高達936 ，遠遠超過815的設計值；噴燃器四周水冷壁結焦嚴重，過熱器管壁溫度超標，無法帶上額定負荷；甚至有時因燃煤質量的變化，必須投油助燃的嚴重情況進行了分析研究。在實際生產過程中，燃燒器的結構、布置，水冷壁的粘污、結垢，過剩空氣系數、一次風溫、煤種及其濃度變化等許多因素都會偏離鍋爐的設計工況，從而影響爐內的傳熱和燃燒，造成爐膛出口超溫、水冷壁結渣等問題。
分享友人