共軸載荷 的英文怎麼說

中文拼音 [gòngzhóuzǎihé]
共軸載荷 英文
coaxial load
  • 共 : 共動詞[書面語]1. （圍繞） surround2. （兩手合圍） span with the hand
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
  • 荷 : 荷名詞（蓮） lotus
  • 載荷 : load; loading載荷變化 load fluctuation; variation in load; 載荷裝置 load device
  1. ( 3 ) by choosing core faultage of axial site in luohu fracture zone i. e. geological cross section in huangbeiling faultage f8 as geological model and utilizing finite element numerical method, change tendency of huangbeiling faultage f8 under self - weight stress and building loads is stimulated. and long - term development trend of fracture zone is also predicted, which has an important guiding meaning for works of geological disaster prevention in district of luohu jiancheng

    （ 3 ）選取羅湖斷裂帶軸部的核心斷層?黃貝嶺f8斷層地質剖面作為地質模型，利用有限元數值方法模擬了黃貝嶺f8斷層在自重應力和建築物荷載共同作用下的變化趨勢，預計出斷層帶的長期發展趨勢，這對羅湖建成區的地質災害防止工作有重要的指導意義。
  2. It shows that the result of resistance under bending and torsion by this method is almost same as that of experiments. correlate equations of bearing capacity of this structure under complex loads are deduced. four expressions of bearing capacity of this structure under complex loads, which are press, bending and torsion, are deduced in the end

    最後利用軸壓、彎曲和扭轉作用的兩兩組合作用下的極限承載力相關方程，通過適當的簡化處理，就得到偏於安全的離心鋼管混凝土構件在軸壓、彎曲和扭轉三種荷載共同作用下的承載力計算公式。
  3. This kind of high silica wrought aluminum alloy is provided with low density and well heat - stability, especially with the metallurgical structur ? similar with bearing alloy ? which is composed of dispersion distribution common silicon crystal hard mass point and the alloyed basal body is very fit for the components manufacture ? can bear small capacity moving load and friction load

    這種高硅變形鋁合金具有密度小和200以下良好的熱穩定性，特別是它的由彌散分佈的共晶硅硬質點及合金化的相基體組成的類似軸承合金的金相組織、特別適合用於製做承受小能量動載荷和摩擦載荷的零件。
  4. In this part, it is also found that the equivalent prismatic column, which is obtained based on the equal elastic critical load as the non - prismatic member, is not actually equivalent to the tapered column in inelastic stability, and the latter has higher load carrying capacity. finally, the behavior of tapered beam - column acted by combined axial load and transverse load has been investigated. a bending - thrust interaction curve is established which is similar to the ones for the design of prismatic members

    三是研究了楔形變截面懸臂構件在大端固定，小端同時承受橫向及軸向荷載共同作用下的強度和彎矩平面內的穩定，同時參考等截面構件的設計公式，得到了用大端截面來表示的軸力p與彎矩m的之間的相關關系。
  5. This paper, in allusion to damage of expansion joint of bridge, introduces a sort of new structure of jointless device - semi - integral abutment jointless bridge, and establishes model of general structure finite element of this bridge, and in details analyses its qualities of stress. the model considers the interaction of superstructure - substructure - soil. resistance of the soil behind abutment adopts still soil pressure and elastic resistance when the temperature rising, but active soil pressure when dropping. analysis of qualities stress of bridge includes of action of dead load, car load, temperature load of season character. taking an 100m length pc semi - integral abutment jointless bridge as instance, the paper establishes the model of plane frame by applying large common software - anasys, and analyses it by elastane and large deformation to imitate character of stress and deformation of general bridge. at the same time corresponding models of finite element of joint bridge and integral abutment bridge are established, and unique stress and performance of structure of semi - integral abutment jointless bridge are researched by comparing and analysing character of three different models under same loading, and controlling factor of design and constitution are generalized. in conclusion, for semi - integral abutment jointless bridge, on one hand shear, moment and deflection of the main beam and axis force of substructure are approximate with that of joint bridge, and integral stifmess of structure is increased and damage of expansion joint is eliminated, on the other hand there is axis force in main beam, shear and moment of substructure are bigger than that of joint bridge. in all this type of jointless bridge has rational stress and is worth of application and popularization

    半整體式橋臺無縫橋梁計算模型考慮了上部結構-下部結構-土的共同作用；臺後土抗力升溫時採用靜止土壓力加彈性土抗力，降溫時採用主動土壓力；分析橋梁受力性能時考慮了結構自重、車輛荷載和季節性溫變荷載的作用。以一座橋長100mpc半整體式橋臺無縫橋梁為實例，採用大型通用軟體ansys建立平面框架模型，進行彈性、大變形分析，模擬全橋受力和變形特點；同時建立與此對應的有伸縮縫橋梁和整體式橋臺無縫橋梁有限元模型，通過三種橋型同步加載對比分析，研究半整體式橋臺無縫橋梁獨特的受力特點和結構性能，總結其設計控制因素和構造要求。通過本文研究知：半整體式橋臺無縫橋梁主梁的剪力、彎矩、撓度和下部結構的軸力與梁式橋相近，結構整體剛度增大，併除去了伸縮縫病害；但主梁增加了軸力，下部結構剪力、彎矩較梁式橋大；綜合分析是一種受力合理有實踐和推廣價值的橋型。
  6. A way to avoiding crack or reducing crack width of concrete or reducing distortion of member is using prestressed concrete. the writer tried to make full use of the merit of the prestressed concrete and designed prestressed concrete mandril to control crack of structure. the prestressed concrete mandril, which was firstly applied high pressure on a small concrete bar, and then was made in concrete, so it would act as reinforced bar and resist load. in this thesis the writer designed 24 mmnbers and had experimental study of them, reached the conclusion that the effect of resisting crack of the prestressed concrete mandril was good when the load was not large, it can enhance the capacity of resisting crack and reduce the crack distance and crack width, but when the loads was large, the effect of resisting crack was not good, when we used the prestressed concrete mandril and reinforced bar together in member, the effect of resisting crack was very good. the writer analysed the adherence mechanism and wreck mechanism of the prestressed concrete mandril in anxial tension members, and according to the character of the prestressed concrete mandril, the writer constructed the bond model of it. then the writer introduced the analysis theory of crack including the bond - slip theory, the non - slip theory, the synthesis theory and mathematics stat method. the different theory had different theory base, they considered that the primary affection of crack width was different. in this test, the crack distance and crack width of members which placed reinforced bar were match to the compute value of the code gb 50010 - 2002 very well. to the members which

    本文共進行了24根試件的試驗研究，得出了預應力混凝土芯棒能較大地提高構件抗裂承載力，在荷載小於預應力混凝土芯棒的開裂荷載時有較好的抗裂效果，能較大地減小裂縫間距和裂縫寬度，但是當荷載較大預應力混凝土芯棒開裂時預應力混凝土芯棒的抗裂效果不是很好，若將普通鋼筋和預應力混凝土芯棒一起使用時則有很好的抗裂效果。本文分析了預應力混凝土芯棒在軸拉試件中的粘結機理和破壞機理，根據預應力混凝土芯棒本身的特點，提出了預應力混凝土芯棒與后澆混凝土之間的粘結模型。然後本文詳細介紹了經典的裂縫分析理論粘結滑移理論、無滑移理論、綜合理論和數理統計方法，各理論有著各自不同的理論基礎，認為影響裂縫寬度的主要影響因素也各不相同。
  7. As far as he hollow inclined column - wall transfer r. c joint is concerned, the stress state of transfer beam is very critical, because it bears not only the vertical load transferred from the wall, but also the axial load initiated by the inclined column

    對有孔斜柱轉換節點而言，轉換梁的受力最為不利，它不僅承擔由薄壁柱傳來的垂直荷載，而且還承擔由斜柱水平分力引起的軸向拉力，即截面上有彎矩、剪力和軸力的共同作用。
  8. After considering the coupling of the mounting errors and elastic deformation, the meshing influences of the error of the center distance, the setting parametric error in the axial direction, and the intersect angle between the two axes on transmission performance are investigated. 4

    考慮到安裝誤差和載荷作用下的彈性變形等非共軛因素耦合作用，分析了漸開線蝸桿傳動在安裝時存在中心距誤差，軸間相對位置誤差，軸間相對夾角誤差對其承載嚙合的影響； 4
  9. Utilize energy method to research crook problem of drilling rod under pressure and act on together, having studied the crooked influence to the drilling rod of torsion emphatically, the theory analyses found that axial load, hole vertex angle and torque are important factors of influence drilling rod crook

    利用能量方法研究了壓力和扭矩共同作用下鉆桿的彎曲問題，著重研究了扭矩對鉆桿彎曲的影響，理論分析發現，軸向載荷，鉆孔頂角和扭矩是影響鉆桿彎曲的重要因素。
分享友人
分享到 Line

分享到臉書