命令重試 的英文怎麼說

中文拼音 [mìnglìngzhòngshì]
命令重試 英文
command retry
  • 重 : 重Ⅰ名詞（重量; 分量） weight Ⅱ動詞（重視） lay [place put] stress on; place value upon; attach im...
  • 試 : 名詞（古代占卜用的器具） astrolabe
  1. A very complex sequence probably won ' t be re - used in many test scripts, so it might not be worth the labor required to generalize it, document it, and insert the error - checking code into it that you would expect of a competently written library function

    因為一個很復雜的命令序列很可能在很多測試腳本中無法重用，所以，就不值得花力氣去生成它，為它寫文檔，並為它加入錯誤檢查代碼以期成為編寫完善的庫函數。
  2. Before the connectting between moden and other equipments, it works at the cammand mode, the cammand that is send to moden is used to set or manipulate the mode, after the connectting between moden and other equipments, it works at connectting mode, at that time, the cammand send from the computer is send to another computer which will pass the moden and telephone line. the moden control cammand is called " at " cammand, all the control manipulation is realized by sending the ascii character to moden, after the moden received the " at " cammand, it firstly judges the cammand, secondly, it analyses and executes the cammand, finnally, it executes a response by sending back a ascii character, during the deseign of below - computer, we introduce in detail the deseign of system hardware and system software, below - computer system hardware and system software, below - computer is made up of microchip collecting and controlling system, which finish the strobe and water level data collection, display and disposal, deal with the communication with the above - computer, the microchip is the centre of data dealing with, the peripheral equipments are made up of data collecttion module, control cammand input module, display module, execute output module, and long - distance communication module

    在moden控制軟體的設計中，詳細敘述了moden正常工作時的幾個重要函數：初始化函數、撥號處理函數、應答處理函數、掛機處理函數，設計並調試了四個函數的通信程序，數據機工作時存在兩種模式，命令模式與連線模式，命令模式是針對功能設置的模式，連線模式是數據傳輸的模式。當數據機未與其他設備連接時，其處于命令模式，這時候下達給數據機的指令是作為數據機本身設置或操作用的；當數據機已經與其他設備連接時，其處于連線模式，所有在此時由計算機送至數據機的信息都將經由電話線傳送到另一部計算機上。專門使用於控制數據機的指令集被稱為「 at指令集」 ，對moden的所有操作（如撥號、應答、掛機等）都可以通過給moden發送ascii字元串來實現， moden在收到at命令后，先對命令進行判斷，接著分析和執行命令緩沖區中的命令，最後以自身的ascii字元對命令作出響應。
  3. Retry this command until the mouse connects. you may have to turn it off and on or press the reset button a couple of times

    不斷重試這個命令直到鼠標連接成功。你應當在一段時間內不斷地關閉並打開鼠標或是按鼠標的重啟按鈕。
  4. In most cases, when you issue a stop command, the current job step is canceled and any retry logic is ignored

    大多數情況下，當發出停止命令后，當前的作業步驟就會被取消，所有重試邏輯都會被忽略。
  5. Chapter 4 introduces emphatically at command of gsm module, the communication protocols of the system and debug measure, furthermore the procedure is programmed to simulate supervise center

    第四章著重探討了gsm模塊的at命令，系統的通信協議，車載臺的軟體實現和調試方法，並創造性地編寫了一個監控中心模擬程序供調試使用。
  6. Number of times the command was retried the last time the step ran

    步驟上一次運行時，重試命令的次數。
  7. Dotfuscators renaming system also provides inherent obfuscation properties far greater than typical renaming systems. many obfuscating renamers rely on renaming to unprintable characters or confusing sequences in attempts to foil decompiled output

    許多進行「模糊處理」的重命名程序依靠將原始內容重命名為不可列印的字元或令人迷惑的序列來試圖干擾反編譯輸出結果。
  8. The portable infrared press instrument has the following characteristics : has small volume and weight and carry easily ; use a keyboard to input orders and display the corresponding information on the lcd display for the sake of the user ' s convenience ; has big data capacity and can collect 30 press measure instruments all the data which have stored for a week ; show the real - time date and time ; communicate through the infrared with speed of 2400kbps ; has the intrinsically safe circuit and can be safely used under coal mine

    本文所研製出的紅外線壓力手抄器的主要特點是：體積小、重量輕、易於攜帶；使用鍵盤輸入命令，並在液晶顯示屏上給予相應的提示，極大地方便了使用者；數據容量較大，可一次採集30臺壓力測試儀一周內存儲的壓力數據；全日歷實時時鐘顯示；紅外數據通訊功能，傳輸速率為2400kbps ；本安設計，可安全的應用於煤礦井下。
  9. When debugging program compiled from the command line, dgbclr rereads the compiled program each time you start debugging

    當調試從命令行編譯的程序時， dgbclr在您每次開始調試時都會重新讀取編譯的程序。
  10. When debugging program compiled from the command line, visual studio rereads the compiled program each time you start debugging

    當調試從命令行編譯的程序時， visual studio在您每次開始調試時都會重新讀取編譯的程序。
  11. Restart portal server and try the xml access command again

    重新啟動門戶服務器並再次嘗試xml access命令。
分享友人
分享到 Line

分享到臉書