噴嘴噴射速度 的英文怎麼說

中文拼音 [pēnzuǐpēnshèsùdù]
噴嘴噴射速度 英文
nozzle velocity
  • 噴 : 噴動詞1. （液體等受壓力而射出） spurt; spout; gush; jet 2. （噴灑） spray; sprinkle
  • 嘴 : 名詞1. （口的通稱） mouth 2. （形狀或作用像嘴的東西） anything shaped or functioning like a mouth 3. （指說話） talk; speak
  • 射 : Ⅰ動詞1 （用推力或彈力送出） shoot; fire 2 （液體受到壓力迅速擠出） discharge in a jet 3 （放出） ...
  • 速 : Ⅰ形容詞（迅速; 快） fast; rapid; quick; speedy Ⅱ名詞1 （速度） speed; velocity 2 （姓氏） a surna...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 速度 : 1. [物理學] velocity; speed; blast; bat 2. [音樂] tempo3. （快慢的程度） speed; rate; pace; tempo
  1. The effect of the height between nozzles and ground plate, the distance between the nozzles, the inlet velocity of the nozzles, and the velocity of the cross flow on the flowfield structure were studied one by one

    分別就噴嘴距地面高度、噴嘴間距、噴嘴出口速度、橫向流等，對噴射垂直撞擊平板流場的影響，逐一討論。
  2. Passing through the nozzle at the highest speed, impulse turbine steam directs against a row of blades which assembled in the axles of impulse turbine with radiation shape

    當蒸汽以最高速度從噴嘴裏噴出時，便沖擊一列呈輻射狀安裝在渦輪機主軸上的動葉片。
  3. According to rigorous procedures, an experimental study was carried out to investigate the effects of jet exit velocity, flow direction, fluid subcooling and nozzle diameter on hysteresis of boiling heat transfer with impinging circular submerged jets of highly - wetting liquids

    摘要系統地研究了液體在圓形斷面噴嘴浸沒射流作用下沸騰熱滯后與射流沖擊速度大小、液體流動方向、液體過冷度和噴嘴直徑等因素的影響。
  4. A reasonable position of driving nozzle helps to achieve the maximum material flow that also depends on other parameters such as backpressure, properties of conveyed material and driving gas. it is observed that, an increase of convergent section angle is harmful to the pneumatic conveying system, and also influences on the mass flow rate of conveyed material, the distribution of static pressures in injector and the pressure drops of conveying pipe. in addition, within a reasonable scope of air mass rate, increasing the driving jet velocity is more advantageous than enlarging the dimension of driving nozzle

    試驗研究發現，氣體噴嘴位置對氣固噴射器的輸送能力影響最大，氣體噴嘴存在某一最佳位置，而這一最佳位置與背壓、輸送物料特性和輸送風特性相關聯；氣固噴射器的收縮角對其輸送能力、內部靜壓分佈和輸送管阻力特性均有適量影響，收縮角增大對整個輸送系統均不利；在適當的輸送風范圍內，提高氣體噴嘴出口速度比擴大氣體噴嘴尺寸更為有利，但氣體噴嘴出口速度過高會增加氣固噴射器和輸送管內的能量損耗，給輸送帶來不利的影響；系統背壓與氣固噴射器的氣體噴嘴出口速度的選取有關。
  5. The influences of the inlet tube angle, backpressure and driving jet velocity on static pressure distribution in the gas - solid injector are calculated, and the effects of the inlet tube angle on particle bulk phase concentration and axial mean speed of particles in the gas - solid injector are analyzed firstly. the predicament caused by lack of measuring means on the particle velocity in experiments is solved

    分析了收縮角、背壓和氣體噴嘴出口速度對氣固噴射器內靜壓分佈的影響，以及收縮角對氣固噴射器內固體顆粒體積濃度場和顆粒平均速度的影響，解決了噴射器內固體顆粒速度試驗測試手段缺乏的困境。
  6. 3. testing all the hydraulic parameters of the sprinkler installed with adjuster such as working pressure, water flux, the range of the sprinkler, intensity of water drop impact, characteristic of water distribution, etc. according to the testing data, we can learn the quantitative relations among the structure of the adjuster, working pressure, diameter of the nozzle, elevation of sprinkler, wind power, velocity of rotation and the range of water

    測試安裝「壓力調節器」后的噴頭的水力性能參數，即工作壓力、流量、射程、水滴的打擊強度、噴灑水分佈特性等。依據所測得的噴頭水力性能參數和射程數據，我們可較清楚的了解「壓力調節器」的結構形式、工作壓力、噴嘴直徑、噴射仰角、風力、旋轉速度和噴頭射程之間的定量關系。
  7. However, by comparison with flap nozzle servo valve which has been used widely and popularly by now, the torque motor of jet pipe servo valve has a larger rotary inertia. this causes low natural frequency of servo valve, and thus the response speed of jet pipe servo valve is slow. moreover, the jet pipe of servo valve has large flexibility, and it is easy to excite oscillations and noise in the valve, which is named self - excited oscillations and noise

    然而與目前普遍使用的噴嘴擋板伺服閥相比，射流管伺服閥的銜鐵組件轉動慣量大，導致力矩馬達部分固有頻率低，從而響應速度慢，此外，射流管供油管柔性大，容易產生自激現象，這些缺點都使得射流管伺服閥的動態特性差，從而影響了它的工作性能。
分享友人
分享到 Line

分享到臉書