噴嘴密度 的英文怎麼說
中文拼音 [pēnzuǐmìdù]
噴嘴密度
英文
ray nozzle de ity-
This paper deriving the theory work inflection point in the static stage characteristics curve of small measurement range linear dimension measurement. by the way of high pressure and back pressure pneumatic measure and designed the parameter of the mainly and measure spray head, which are the key component in the spray head - baffle pneumatic sensor. the different groups for the main - spray head and the measure spray head, will effect the dynamic and static stage characteristic parameter. the author have done contrast experiment and optimization design to test and verify the theory derivation whereby made the rang of show valve of pneumatic measure system measure range up to 40 u m, the sensitivity up to 100mv / u m, resolution up to 0. 05 p m, the uncertainly of measure is less than 0. o2 u m, satisfaction of requirement of groups the carboy hatch thickness size precise measure of soft shims
對高壓背壓式氣動測量用於小量程線性尺寸測量的靜態特性曲線的理論工作拐點進行了推導,對氣動測量系統中的噴嘴-擋板型氣動傳感器中的關鍵部件? ?主噴嘴和測量噴嘴的參數進行了理論設計,對主噴嘴和測量噴嘴的不同組合,將影響測量系統靜、動態特性指標的噴嘴參數進行了對比實驗和優化設計,並通過實驗驗證了理論推導,從而使氣動測量系統量程的示值范圍達到40 m ,靈敏度達到100mv m ,解析度達到0 . 05 m ,測量不確定度小於0 . 2 m ,滿足了壓縮機缸蓋軟體墊片厚度尺寸精密測量分組的要求。The spray nozzles are designed to produce a dense spray at a predetermined angle.
噴嘴是按預定角度產生稠密水霧來設計的。Through the controls of geometric dimension of micro - nozzle and driving frequency to obtain the volume of droplets in the grade of pico to femto litre, which is applicable to make high density micro - array
通過微噴嘴幾何尺寸控制和驅動頻率控制獲得從飛升到皮升級樣點體積,可以用於製作高密度的微陣列。The results showed that the processing parameters ( such as laser power, the diameter of laser, scanning speed of laser beam, ratio of overlapping ) are important to acquire a perfect component. furthermore, in order to assure geometric properties ( accuracy, surface finish ), the structure of the off - axial powder nozzle was improved to avoid the oxidation of the molten pool. the density metal test sample of rene95 high - temperature alloy was made by lsf through optimizing the processing parameters
本文對激光立體成形的工藝特性進行了深入系統的研究,發現如果要獲得理想的成形效果,就必須對成形過程中的工藝參數進行精密控制,例如激光功率、激光光斑大小、光束掃描速度、搭接率等;同時為了保證成形件有較高的尺寸精度和表面質量,必須對成形零件的氧化問題進行控制,通過改進側向送粉噴嘴的結構設計,成形件的表面氧化問題得到適度控制。The results show that the improved structure has obviously reduced pressure drop and increased axial speed of the nozzle, as a result the wallop of electroplating solution is improved and the thickness of diffused layer reduced, the electrodeposition process improved, and what is more, the coating structure has been compacted, crystalline particles fined and the performance improved
結果表明,結構改進后,明顯減小了壓力損失,提高了噴嘴的抽向速度,電鍍液沖擊鍍件的沖擊力得到提高,有效地減少了擴散層的厚度,改善了電沉積過程,而且使鍍層組織緻密,晶粒細化性能得到提高。Facilitate multi - set jet pipes and high - density nozzle according to client treatment volume
有依客戶設置之多組噴流管及高密度噴嘴。分享友人