嚙合部 的英文怎麼說

中文拼音 [niègěbù]
嚙合部 英文
engaging piece
  • 嚙 : 動詞[書面語]1. （鼠、兔等用牙啃或咬） gnaw （at） 2. （侵蝕） erode
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 部 : Ⅰ名詞1 （部分; 部位） part; section; division; region 2 （部門; 機關或組織單位的名稱） unit; mini...
  1. Tolerancing of bevel gears ; basic concepts

    傘齒輪嚙合公差.第1部分:基本概念
  2. We have in - house rolling, forging and machining capability to manufacture all types of fishplates including plain, joggled, angle, and combination fishplate to various drawings for various rails

    我們有內部的軋輥，鍛造和機床加工這樣的技術，有能力去生產所有類型的魚尾板包括普通魚尾板，嚙合型魚尾板，角形魚尾板和組合型魚尾板根據各種各樣的圖紙為各種各樣的鐵路。
  3. Specification for components for commercial vehicles and buses - cross - tooth propeller shaft flanges, type t

    商用車輛和公共汽車用部件規范. t型嚙合傳動軸法蘭
  4. Size and obliquity of tooth directly influence clutch whether normal operating. it is a key part for ensuring normal operating of aira too. this article fully deduces their compute formula

    該齒形的大小、傾角直接影響離合器是否能正確地嚙合和分離，也是保證機構進行正確工作的關鍵部分，本文詳盡推導了它們的計算公式。
  5. Specification for continuous mechanical handling equipment - safety requirements - conveyors and elevators with chain - elements - examples for guarding of nip points

    連續式機械裝卸設備規范.安全性要求.第18部分:鏈節式輸送機與升降機-嚙合點保護示例
  6. ( 3 ) in the condition of invariable instantaneous speed ratio, the equations of teeth surface of all key components, such as end face gear, oscillating teeth, wave producer, et al, are deduced

    （ 3 ）在保證瞬時傳動比恆定的條件下，由空間嚙合原理出發，重點推導了活齒端面諧波齒輪傳動裝置的主要傳動部件? ?端面齒輪、活齒以及波發生器端面凸輪的齒面方程。
  7. Spur and helical gears - definitions and allowable values of deviations relevant to radial composite deviations and runout information

    齒輪和螺旋齒輪.第5部分:齒輪齒根嚙合面偏差容許值和定義
  8. Cylindrical gears - iso system of accuracy - part 1 : definitions and allowable values of deviations relevant to corresponding flanks of gear teeth

    圓柱齒輪. iso精度體系.第1部分:齒輪嚙合對應齒根面的相應偏差定義和容許值
  9. 4. calculate the engaging distance between inserts and slots and the least thickness from bearing to contour of cone automatically. 5

    自動計算相鄰牙輪之間牙齒與齒槽的最小嚙合間隙和牙齒底部到牙輪內孔的最小壁厚。
  10. Connectors for electronic equipment - tests and measurements - part 13 - 1 : mechanical operating tests - test 13a : engaging and separating forces

    電子設備連接器.試驗和測量.第13 - 1部分:機械操作試驗.試驗13a :嚙合力及離散力
  11. Dental handpieces. part 2 : straight and geared angle handpieces

    牙科機頭.第2部分:直角和嚙合角機頭
  12. Information on gear teeth in drawings ; information on involute teeth for cylindrical gears

    圖紙上齒輪嚙合信息第1部分:圓柱齒輪漸開線嚙合信息
  13. Master gears for checking spur gears ; gear blank and tooth system

    正齒輪檢驗用標準齒輪.第1部分:齒輪坯和嚙合體系
  14. Tabular layouts of properties - part 140 : toothing system data of work pieces

    特性表.第140部分:工件的嚙合系統數據
  15. The indexing pawl advances a fastener into operative engagement with the feed pawl upon movement of the second canister portion from the open position to the closed position

    當第二筒部從打開位置移動到關閉位置時，分度棘爪使緊固件前進並使其與進給棘爪工作嚙合。
  16. Tolerancing of bevel gears ; tolerances for shaft angle errors and axes intersection point deviations

    傘齒輪嚙合公差.第4部分:軸線夾角誤差及軸線交叉點偏
  17. Due to the unsteadiness of the vibration signal, conventional methods of gear fault diagnosis based on steady signal processing, which consist of time domain and frequency domain analysis method, are not as effective to local defect as to dispersed defect of gear

    傳統的齒輪故障診斷方法（包括頻域分析方法和時域分析方法）對于齒輪的分佈故障有很好的診斷效果。但當齒輪產生局部故障時，失效的輪齒間斷地進入嚙合，產生沖擊振動，使得齒輪振動信號包含了非平穩或時變成分。
  18. Information on gear teeth in drawings ; information on straight bevel gear teeth

    圖紙上齒輪嚙合信息第2部分:直齒傘齒輪嚙合信息
  19. Stations use hardpoints just like ships, so do not forget to place static hardpoints on large, flat surfaces in strategic locations, so that it is able to defend itself

    檢查模型的嚙合情況，確保不留縫隙。雖然小溝小洞在遠距離不容易發覺，但如果小型載具飛近空間站站體，就很可能穿越縫隙飛到空間站站內部。
  20. Dental handpieces - part 2 : straight and geared angle handpieces iso 7785 - 2 : 1995 ; german version en iso 7785 - 2 : 1997

    手持式牙科器械.第2部分:平角和嚙合角手持式器械
分享友人
分享到 Line

分享到臉書