圓柱體強度 的英文怎麼說
中文拼音 [yuánzhùtǐqiángdù]
圓柱體強度
英文
cylinder strength-
Standard test method for compressive strength of concrete cylinders cast in place in cylindrical molds
在圓柱模型中現場澆注混凝土圓柱體的抗壓強度標準試驗方法The test shows that nominal transverse splitting strength of concrete cylinder is well correlated to the concrete cube strength and splitting strength of cube and cylinder, especially, above interrelation is more ideal when hold - down central angle is 90
經試驗證明，混凝土圓柱體的橫劈名義強度與混凝土的抗壓強度、立方體及圓柱體縱劈強度有很好的相關性，尤其當壓具圓心角為90時，上述關系更為理想。Standard practice for making test cylinders and prisms for determining strength and density of preplaced - aggregate concrete in the laboratory
在實驗室內進行預置集料混凝土的密度和強度試驗用圓柱體和稜柱體製作試驗的標準規范Abstract : this paper derives thecalculating formulas to the contact strength and oil - film thickness of the involute spur gear according to hydrodynamic lubrication principle. through check with test, shows that they may rully replace now available hertz formula and dowsonformula respectively
文摘:根據流體動力潤滑原理，推導出了漸開線直齒圓柱齒輪接觸強度及油膜厚度的計算公式，通過實驗驗證，說明它們可以完全分別代替現有的赫芝公式及通森公式。For the scattering field caused by the finite - length conducting and permeable cylinder, the boundary condition that the normal component of electrical strength is zero in conducting medium, i. e. en = 0, was used to determine the separation constant of boundary value problem in the past
以往含有有限長導電導磁圓柱體散射場的求解，大都根據導電媒質中電場強度法向分量為零，即e _ n = 0 ，這一邊界條件來確定邊值問題中分離常數的取值。In order to verify the feasibility of the present method, chapter 3 takes the fluid flow of sphere, cylinder and the additive mass of two spheres as three examples, finishes the calculation by disposing the source or sink whose strength is expressed as the format of nurbs and emphatically the processing of the singular integral. it can be drawn from the comparison of the results of present method and the theoretical solution, i. e. a good precision can be gotten under a few collocation points with the method
為了考查本文方法的可行性，第3章以圓球體繞流、圓柱繞流以及兩個等圓球體在流場中的附加質量作為例子，通過在物體表面布置強度以非均勻有理b樣條表達的源匯和著重對奇異積分的處理后完成了相應的計算，從與理論解的比較可以看出本方法的優越：在數目很少的配置點下數值解可取得十分良好的精度。The calculating mold consisted of shell, pyramidal neck of shell with varied thickness, flange of ring with definite thickness for analytic solution is set up for the strength calculation and the design of the structure dimension of shell flange and pyramidal neck. this theoretic solution is compared with the results of finite element analysis and stress - strain measurement and is verified to be right
為設計計算烘缸法蘭及錐頸的強度與結構尺寸要求，建立以簡體、具有斜面的變厚度圓柱殼的錐頸及具有一定厚度圓環的法蘭環為解析解的計算模型，進行應力求解，將該理論解與有限元分析及應力應變實測結果進行分析對比，驗證該解結果的正確性。Beased on the theory of hertz stress, the contact stress of roller bearing is analysed in this paper
摘要依據赫茲接觸強度計算理論，著重研究了圓柱滾子軸承內、外圈及滾動體的接觸應力。分享友人